Last seen: Sep 18, 2025
@toodles Yes, there should be - there is the required 600mm distance from the wall.
@kenbone Thanks Ken, that is really helpful. With some trepidation, could I point out an inconsistency in your guide? On page 12 FSV 2091 External T...
@ken-bone Thanks so much for such a clear explanation of the positioning of one or more anti freeze valves. I was planning to have one installed in my...
I think you are quite correct as long as the extra volume is in your radiators. The more emitters that you have, the more heat will be emitted, which...
@editor This advice seems to fly in the face of everything I have learnt from the likes of @iancalderbank and @heacol . Perhaps that is why you have a...
As Mars says, the Samsung will cycle when the heat emitted by the radiators is lower than the minimum power that the heat pump can modulate down to - ...
Hi Ian, yes you are mistaken. The water volume in the primary loop with a heat exchanger is always going to be small. This a quote from Graham Hendra'...
You have what is sometimes referred to as flow separation. In your case this is done using a heat exchanger and in most other Samsung systems that I k...
@iantelescope You should see Set indoor and this is adjustable. However weather compensation still operates just as it did when using an external s...
This is incorrect. This setting allows you to use the thermostat in the wired controller and set up room temperature mode. The water law settings stil...
@allyfish What is the rationale for your requirement to fit anti-freeze valves on both supply and return pipes? This is contrary to what @heacol recom...
@heacol Thanks Brendon, that is very helpful.
Latest Posts
-
RE: Testing new controls/monitoring for Midea Clone ASHP
Perhaps they didn't significantly rewrite the algorithm...
By JamesPa , 23 minutes ago
-
based on the information I have I completely agree, alt...
By JamesPa , 33 minutes ago
-
RE: IVT Greenline high pressure switch and electrical cassette errors
Hi, apologies for piggybacking on this thread. I also h...
By Get , 52 minutes ago
-
RE: RDSAP10 effect on existing heat pump EPC rating?
@mike-patrick maybe pickup this ChatGPT conversation an...
By Tim441 , 2 hours ago
-
RE: How can I programme a setback for my Samsung Gen6 8kW heat pump?
Yes, and probably also Adia although the latter has a m...
By JamesPa , 2 hours ago
-
@editor I am all in favour of provocati...
By GrahamF , 6 hours ago
-
@editor lol. I wish. They told me to switch everything ...
By bontwoody , 7 hours ago
-
RE: How to Understand Wiring Up a Heat Pump
Morning, On top of what everyone else I would deffo loo...
By Grantmethestrength , 12 hours ago
-
RE: Help me keep the faith with my air source heat pump installation
@adamk I have seen the openenergymonitor thread, in fac...
By JamesPa , 12 hours ago
-
RE: Sizing a heat pump: Save me from my headache
Got the results back from the one we’re ...
By Mikeatthezoo , 23 hours ago
-
RE: Renewables & Heat Pumps in the News
Thanks Lucia. I'll set aside some time to go through th...
By Transparent , 2 days ago
-
RE: Do I just go with the lowest quote for my heat pump?
Seems to be settling better now I'll leave it alone
By Jancold , 2 days ago
-
RE: Bosch CS5800i 5kW - Experience So Far
We do like the exhaust air heat pump as a centralised M...
By Steelbadger , 3 days ago
-
RE: Solar Thermal DHW and ASHP
@kenbone how is your battery holding up Ken? Still goin...
By Mars , 3 days ago
-
RE: Air source heat pump roll call – what heat pump brand and model do you have?
Old Samsung R410a unit 9kw, modbused controlled, let Ha...
By KenBone , 3 days ago
-
RE: Replacement Inverter for old FIT system
@bontwoody I have a single string 3kW solar AC inverter...
By Old_Scientist , 3 days ago
-
Octopus removed our gas meter for free a couple of year...
By robl , 3 days ago
