Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Apr 15, 2026
Just a quick update, during the cold spell I went full WC but I ran into a different issue, the flow temp would max out at around 36c when it asking f...
WOW - thank you so much for the time you spend working this out, had a Quick Look and I def need to look super close to try and understand all those n...
I’ll have to go with hours as the 0.9 is not timed but triggered by low temperature breach via thermostat. But I can estimate hours on each from the p...
The Kitchen and pretty much all the rooms upstairs except my daughters bedroom for some reason maybe as hers is south facing.
You will love this, regards the house config, different improvements have happened at different times, hence the mix-mash, at one point we had 2 gas b...
The house has not been turned upside down, bedrooms are all upstairs. So the way you would start and sorry to keep going on - would be that you set ...
Let me try answer what I know.Yes it's the same pump, and original design and install had the whole system as 1 the only limit was on the control unit...
I am not sure this is an option for me at all, if my heat curve is low the downstairs will be fine but upstairs and kitchen will be cold, if I set it ...
Think I figured something out for once. Adaptive heat curve was on, I believe this was adjusting my heat curve automagically, turned it off see if it...
Noise reduction I have no plans so I assume is off always. Bizarre part I noticed is my heating curve was set to 0.5 - I change it to 0.3 and 0.9 an...
I do not believe it's in quiet mode - what setting is that so I can double check? I believe the volume should be fine, as I have a 150l Volumiser an...
Back -- So between 2am and 6:30am it's trying to reach a target temp of 40-42c, it's obviously trying to get there and cycling around every 20 minutes...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Where heat loss surveys seem to go against practical reality
I am amazed that there is not something out there to me...
By JamesPa , 3 hours ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
@bobflux The hydraulic simulator is very interesting...
By Rob of York , 9 hours ago
-
RE: 7kW EV Charger Options Advice
Thanks. Yes, we have patchy 4G. The only option we had ...
By Rusty , 14 hours ago
-
-
RE: Being screwed over by Volkswagen Audi Group
Thanks, @batpred. That integration is the one I have in...
By Majordennisbloodnok , 1 day ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@batpred I suspect it will be more this year. I had 9 ...
By AndrewJ , 1 day ago
-
RE: Surface mount or bury primaries for heat pump installation?
@jamespa It's rusting 🙂
By tomasmcguinness , 1 day ago
-
RE: Glass lined Cylinder for private water supply
Thank you, once again, for your replies. Yes...
By ian33a , 1 day ago
-
It’s been out a few days and Amazon has already attache...
By Mars , 1 day ago
-
RE: Missing flow temperature in Heat Geek proposal
Yes, and this is another point I agree. We did find a f...
By Batpred , 2 days ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
A very good point. In effect, the DHW pipework is an em...
By cathodeRay , 2 days ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@tim441 Here are those same three month periods for 202...
By Toodles , 4 days ago
-
RE: Adding additional Solar Panels to a DC coupled battery system
@transparent thank you for your reply above. As alway...
By Old_Scientist , 5 days ago
-
RE: Adventures in heat loss calculations
@rob-of-york — thanks for posting this, all very useful...
By cathodeRay , 6 days ago
SPONSORS
