Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Sep 6, 2026
Bio-diesel / HVO is used extensively in Cornwall, Devon and SomersetIt's bought by rural properties who use oil boilers for central heating. Instead...
I don't think that's difficult... ... unless you want to keep changing your mind. Most inverters have RS485 ports which communicate using Modbus.T...
As the owner of a small wind-turbine for three years (until it caught fire), I've been able to assess first hand whether they are worthwhile. &nbs...
Erm... we discussed the direction of GivEnergy's product design last year on this Forum. They are migrating away from the low-voltage systems throug...
I think we'd need to research a bit deeper as to how those two inverters handle the concept of exporting to the grid. If both were configured to all...
Proposed grid voltage changes The Energy Networks Association intends changing the Electricity Safety Quality and Continuity Regulations (s...
True... but I'll be the one derailing this topic if I respond here. Firstly I know how to reduce the number of power cuts, in which we can ...
Does this mean that you're intending a self-install of a storage battery? You won't need strong biceps to run it after the installer leaves site &#x...
@jamespa – fuses and trips must be rated according to the current-carrying capacity of the cable, not calculated on the load(s) you intend to supply. ...
SPONSORS
Degrees of Separation
Latest Posts
-
Panasonic Free Multi Z and Etherea Internal units.
My prospective installers have suggested the Panasonic ...
By Toodles , 4 hours ago
-
RE: Where heat loss surveys seem to go against practical reality
OK, this one is fairly easy, because most of what is ne...
By cathodeRay , 4 hours ago
-
Hi @jamespa , @trebor12345 ,Thank you both for the repl...
By rgabor , 4 hours ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
Great. You just need to find a way of cranking up your...
By JamesPa , 5 hours ago
-
RE: Heat Pumps Without Grants: Would You Have Installed One & Will You Now?
We had two heat pumps installed without Govt funding. H...
By Rob of York , 5 hours ago
-
RE: 7kW EV Charger Options Advice
I’ve had an EV with wall charger for over 3 years and t...
By AndrewJ , 12 hours ago
-
My Adapt is finally installed and running! Almost a yea...
By tomasmcguinness , 12 hours ago
-
-
RE: Being screwed over by Volkswagen Audi Group
Thanks, @batpred. That integration is the one I have in...
By Majordennisbloodnok , 3 days ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@batpred I suspect it will be more this year. I had 9 ...
By AndrewJ , 3 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@jamespa It's rusting 🙂
By tomasmcguinness , 3 days ago
-
RE: Glass lined Cylinder for private water supply
Thank you, once again, for your replies. Yes...
By ian33a , 3 days ago
-
It’s been out a few days and Amazon has already attache...
By Mars , 3 days ago
-
RE: Missing flow temperature in Heat Geek proposal
Yes, and this is another point I agree. We did find a f...
By Batpred , 3 days ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
A very good point. In effect, the DHW pipework is an em...
By cathodeRay , 4 days ago
SPONSORS
