Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jul 29, 2026
I don't plan to use this, as our property is subject to tree shading from trees with TPO's on them, so was always going to be a limiting factor for us...
I'm not sure why the specific hardware would be deemed to be making any difference to what Havenwise is doing, or learning, from your system as it tak...
It's buried within what has become my ongoing post-installation 'diary' thread, but I'd had interactions with most of the companies named within the e...
I've been in receipt of the Green box for 48 hours now, and having had no prior experience of Home Assistant to this point, these are my initial thoug...
Hi @f1p I'm finding the basic analysis available within MelPump really useful, even without having added the dongle as yet.One query on something that...
The initial Aira appointment, certainly in my case when I booked it, is advised as a consultation, taking around an hour, and not a full heat loss sur...
Unless it's changed in the last few months, Octopus' survey cost is a fully refundable deposit, and they'll do the EPC too as part of that. I used t...
This is pretty much my experience of the Zappi, and I'd second the recommendation for it. I've spotted recently that Myenergi have a new charger mode...
This post, on my 'diary' thread, might be of interest in providing some insight into what's available from both systems. I've been using both to anal...
This is Havenwise moving the MelCloud settings so that they don't interfere with their system instructions. Room temperature is set to maximum (29.5)...
I'll post something to advise my thoughts in due course (and I always have @benson to blame for awakening this monster within me, so if it's negative ...
@sand Good to know that it lifts off, rather than swings as a hinge, as I wasn't sure it would have the clearance. I do have the same screwholes as y...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: 7kW EV Charger Options Advice
@rusty Looks like there’s plenty of room in there for a...
By AndrewJ , 53 minutes ago
-
RE: Where heat loss surveys seem to go against practical reality
@cathoderay I think there is a reasonable argument t...
By Rob of York , 3 hours ago
-
Panasonic Free Multi Z and Etherea Internal units.
My prospective installers have suggested the Panasonic ...
By Toodles , 6 hours ago
-
Hi @jamespa , @trebor12345 ,Thank you both for the repl...
By rgabor , 7 hours ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
Great. You just need to find a way of cranking up your...
By JamesPa , 8 hours ago
-
RE: Heat Pumps Without Grants: Would You Have Installed One & Will You Now?
We had two heat pumps installed without Govt funding. H...
By Rob of York , 8 hours ago
-
My Adapt is finally installed and running! Almost a yea...
By tomasmcguinness , 15 hours ago
-
-
RE: Being screwed over by Volkswagen Audi Group
Thanks, @batpred. That integration is the one I have in...
By Majordennisbloodnok , 3 days ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@batpred I suspect it will be more this year. I had 9 ...
By AndrewJ , 3 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@jamespa It's rusting 🙂
By tomasmcguinness , 3 days ago
-
RE: Glass lined Cylinder for private water supply
Thank you, once again, for your replies. Yes...
By ian33a , 3 days ago
-
It’s been out a few days and Amazon has already attache...
By Mars , 3 days ago
-
RE: Missing flow temperature in Heat Geek proposal
Yes, and this is another point I agree. We did find a f...
By Batpred , 4 days ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
A very good point. In effect, the DHW pipework is an em...
By cathodeRay , 4 days ago
SPONSORS
