Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Aug 1, 2026
That's not a particularly long run. There are other pipe options than copper which provide better choices for retro-fitting below floors and above c...
@broadsman - I'm unsure if those suggestions from @saenergy will be clear enough for you. Allow me to expand some of those terms and concepts: ...
@broadsman - I think you should also consider a partial DIY approach. Elsewhere on this forum we've discussed the battery enclosures made by Seplos,...
Whether you decide to manually release air from an 'automatic' valve rather depends on how much air is in the system, and what amount of exercise you ...
The incomer cable probably only has a size-rating once every meter.The OF 462-467 doesn't give me enough information without also knowing the cable ma...
Yes, I noted that your first post on this topic said But I'm unsure whether it was 'working well' because it was relatively easy to push through ...
Have a closer look and see whether these are tight elbows or swept bends. You might also want to view the comparison between smooth bends and ...
We also ought to consider if the flow is being reduced by sharp elbow joints in the pipework. There is a considerable loss of pressure if standard ...
That's a very useful photo @jancoldIt provides me with heaps of issues which need a comment! 1: The "new" Service Fuse must've been installed by...
The board on which you have the Service Fuse and Meter shouldn't be used for other equipment. I don't see how a separate (small) consumer unit could...
The height of a Smart Meter is 175mm including the Communications Hub. It will need at least 60mm below it to accommodate the bend in the tails. ...
You're contemplating staying cold until Spring?! Is the reason that you can't get your hand to the valve because of the close proximity of the pipes...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Solar Power Output – Let’s Compare Generation Figures
Production resumed to normal once the issue ...
By MK4 , 31 minutes ago
-
RE: Aircon - in listed buildings
@etchedpixels i don't look forward to all the listed n...
By Tim441 , 59 minutes ago
-
RE: Who's your electricity provider and what's your tariff?
@agentgeorge I blame the dishwasher etc.😉 Toodl...
By Toodles , 2 hours ago
-
RE: Love veg, hate watering cans
Oh, I’m convinced about using grey water but not for ve...
By Majordennisbloodnok , 11 hours ago
-
RE: Digest of UK Energy Statistics
That sounds painful. It would be much better to charg...
By Transparent , 13 hours ago
-
Hole diameter is small but hole length is also very sma...
By bobflux , 15 hours ago
-
RE: Are Wind Turbines Really “Losers”?
We were sailing near a wind farm in the North Sea last ...
By Jeff , 15 hours ago
-
@trebor12345 The idea is to ensure that Powerwall knows...
By Toodles , 18 hours ago
-
RE: Indevolt Batteries UK Support & Info Thread
'hard limited' could be in 'admin' password protected s...
By JamesPa , 2 days ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
Thanks. I do both, depending on purpose. For a quick po...
By cathodeRay , 2 days ago
-
RE: Missing flow temperature in Heat Geek proposal
@batpred That makes sense! Thanks for the information.
By sttpd1917 , 2 days ago
-
And we're back to @editor's point about supplier depend...
By Majordennisbloodnok , 3 days ago
-
RE: Cleaning solar panels with a hosepipe
This is one reason I'd never make a good solicitor. I'm...
By Majordennisbloodnok , 3 days ago
SPONSORS
