Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jun 11, 2026
Daikin has a slope WDC which changes per degree of temp change I think. Never used that one myself. The more commonly used one has the two points at e...
I was thinking something similar to the OP half way through the episode still worth a watch of course. Emitter type, delta-T & WDC steepness are...
Just a suggestion but upload your images to an AI agent such as Grok with a full description of your installation and you will get a good description ...
The switch from WDC to LWT i.e. pure WC is fairly straight forward. Your current WDC will apply to the LWT mode except now your thermostat is a read o...
Or a minimum standard for data collection. The Daikin MMI gives unusable graphs on the tiny MMI interface. There are sums for input and output on diff...
My MMI is in the loft but I checked the pump flow rate when running the DHW cycle and it was 25 l/h and I could hardly tell it was running. So now I k...
If the Delta T is easy to configure then just try it as you appear to have very good data collection as standard. So if the pumps are external and not...
@jamespa Small mid-terrace so everything is is in closr proximity. Only thing I could do is try to swap the cheap plastic pipe clips for rubber isolat...
My 4KW Daikin will heat my 180L tank in 30 mins to 48C. Most likely less demand but in the ball park. The COP is not as mine reports 2 at worst. I o...
After installation the system did develop a noise in the volumizer and that turned out to be a bleed valve. Which when fixed caused a squeal in the ba...
So after a week of playing with the LWT mode I'm now back to setting my WDC LWT minimum flow temp to 25C. Below this the HP does not resume reliably t...
This is how Adam from Heat Geeks advocates as the best way to set up a heat pump. Then, once you've established a decent WDC matched to your property'...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Where heat loss surveys seem to go against practical reality
@ian33a — I'm not so sure about the numbers in the last...
By cathodeRay , 10 minutes ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
@bobflux The hydraulic simulator is very interesting...
By Rob of York , 3 hours ago
-
RE: 7kW EV Charger Options Advice
Thanks. Yes, we have patchy 4G. The only option we had ...
By Rusty , 8 hours ago
-
-
RE: Being screwed over by Volkswagen Audi Group
Thanks, @batpred. That integration is the one I have in...
By Majordennisbloodnok , 23 hours ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@batpred I suspect it will be more this year. I had 9 ...
By AndrewJ , 23 hours ago
-
RE: Surface mount or bury primaries for heat pump installation?
@jamespa It's rusting 🙂
By tomasmcguinness , 24 hours ago
-
RE: Glass lined Cylinder for private water supply
Thank you, once again, for your replies. Yes...
By ian33a , 1 day ago
-
It’s been out a few days and Amazon has already attache...
By Mars , 1 day ago
-
RE: Missing flow temperature in Heat Geek proposal
Yes, and this is another point I agree. We did find a f...
By Batpred , 1 day ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
A very good point. In effect, the DHW pipework is an em...
By cathodeRay , 2 days ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@tim441 Here are those same three month periods for 202...
By Toodles , 3 days ago
-
RE: Adding additional Solar Panels to a DC coupled battery system
@transparent thank you for your reply above. As alway...
By Old_Scientist , 4 days ago
-
RE: Adventures in heat loss calculations
@rob-of-york — thanks for posting this, all very useful...
By cathodeRay , 6 days ago
SPONSORS
