Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jun 11, 2026
You can try adjusting the Modulation & Overshoot settings in the MMI to start with. Enter installer mode to adjust these.
My 2 bed mid-terrace definitely dropped consistently after the heat pump was installed. Previously, because I still have single glazing, I used a smal...
Plus the pipe is in contact with the ground so it's a cold/moisture bridge and needs to be lifted or at least an air gap created underneath.
If it's accessible then it should be fine. The cylinder won't get even warm on the outside. Mine is in the loft which was annoying for about 3 weeks...
If it's accessible then it should be fine. The cylinder won't get even warm on the outside. Mine is in the loft which was annoying for about 3 weeks...
I found because I have very low heat loss I can set back the temp by only 1C during the higher rate periods because the Daikin overshoots 1-1.5C regar...
Three things that caused noise in my system after commissioning. Volumiser was gurgling which just turned out to be the air bleed valve not open. ...
@georgea You system isn't too different from mine. I don't have UFH and my house is a 2 bed mid-terrace so maybe a bit smaller. Heat loss 3.3 @ -3C...
Slight correct to the above defrost behaviour as the fan only ramps at the beginning and end of the cycle. The bit in the middle is when both the wate...
ASHP Model: Daikin Altherma 3M 4KW House loss: Calculated 3.3 at -3C, definitely overestimated though. Control mode: Weather Comp + Thermostat wit...
With existing rads it seems easier to just install A2W. I've seen some larger houses with multiple internal A2A units have pipework running all over t...
Valiant & Daikin have a form of load compensation or room influence which can dynamically adjust the WDC by a few degrees based on what thermostat...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Where heat loss surveys seem to go against practical reality
@rob-of-york Interesting that you mentioned this as an ...
By ian33a , 28 minutes ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
@bobflux The hydraulic simulator is very interesting...
By Rob of York , 2 hours ago
-
RE: 7kW EV Charger Options Advice
Thanks. Yes, we have patchy 4G. The only option we had ...
By Rusty , 7 hours ago
-
-
RE: Being screwed over by Volkswagen Audi Group
Thanks, @batpred. That integration is the one I have in...
By Majordennisbloodnok , 22 hours ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@batpred I suspect it will be more this year. I had 9 ...
By AndrewJ , 22 hours ago
-
RE: Surface mount or bury primaries for heat pump installation?
@jamespa It's rusting 🙂
By tomasmcguinness , 23 hours ago
-
RE: Glass lined Cylinder for private water supply
Thank you, once again, for your replies. Yes...
By ian33a , 1 day ago
-
It’s been out a few days and Amazon has already attache...
By Mars , 1 day ago
-
RE: Missing flow temperature in Heat Geek proposal
Yes, and this is another point I agree. We did find a f...
By Batpred , 1 day ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
A very good point. In effect, the DHW pipework is an em...
By cathodeRay , 1 day ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@tim441 Here are those same three month periods for 202...
By Toodles , 3 days ago
-
RE: Adding additional Solar Panels to a DC coupled battery system
@transparent thank you for your reply above. As alway...
By Old_Scientist , 4 days ago
-
RE: Adventures in heat loss calculations
@rob-of-york — thanks for posting this, all very useful...
By cathodeRay , 6 days ago
SPONSORS
