Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jun 10, 2026
Several years ago we went away for a weekend in the middle of a cold snap and without giving any thought to the heat recovery time I turned the heatin...
It did cross my mind but I'm trying to ignore that so please don't remind me 🤣 Hopefully the loss will be very small. I will try it once the...
That is quite concerning as I have a Samsung Gen 6 in our current house and have just had a Gen7 R290 installed in what will be soon be our new home. ...
I leave the zappi in eco+ so it doesn't allow the car to charge and have a boost timer set from 23.30 to 5.30 and the ready by time on Octopus set for...
With a 'blower door' test. I assume at 50pa as that is the pressure that is always mentioned. I have read that the pressure can be increased to try a...
The best thing to get the heat from the UFH to the house is concrete screed and tiles. We have 60mm screed and tiles and the floor stays warm for seve...
Passive house standard is 0.6ACH if I remember correctly so 0.5 is a low figure. I know someone who built to passive standard and was very careful wi...
Well, I guess I will see how it goes, but it does sound like the pump is a 'nice to have' but needs using a little carefully if it isn't going to cool...
@ngillam @marzipan71 Did either of you test out the best way to run your pump to be as efficient as possible? Our heating system is being fitted at t...
My understanding is Homely sets the target flow temperature and switches the heating or DHW on or off. The Samung controller carries on as it was set ...
The reason I said the voltages vary slightly is because the Solis inverter has a screen that shows the grid and inverter voltages for each phase, alon...
SPONSORS
Degrees of Separation
Latest Posts
-
@jamespa Also this coming winter I am going to run my c...
By kilgorexv , 1 hour ago
-
RE: Heat Geek mini store vs pump size
Yes I agree, that’s why Heat Geek have most likely sele...
By Tomtheheatingengineer , 4 hours ago
-
RE: Who's your electricity provider and what's your tariff?
@chandykris Swings and Roundabouts, you win some…. ...
By Toodles , 5 hours ago
-
@tomtheheatingengineer, thank you, and welcome to the f...
By Mars , 13 hours ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
@majordennisbloodnok @tomtheheatingengineer For my ...
By JamesPa , 13 hours ago
-
RE: Do I add Air Con or MVHR to existing A2W ASHP?
There is scope for product development here. I for one...
By JamesPa , 15 hours ago
-
RE: Is the "divide by 2900" rule still valid?
Really flow rate is a pipework limitation not a water p...
By JamesPa , 1 day ago
-
RE: The good, the bad and the not that great – my heat pump installation
@burtis, I’ve followed this thread pretty much from the...
By Mars , 4 days ago
-
RE: Starting Our Heat Pump Journey: 1962 build 3 bed detached house
First time poster here but I can share my experience as...
By SCH , 4 days ago
-
RE: Is it the house or the equipment?
...which, I've found out, is pretty much impossible to ...
By Majordennisbloodnok , 5 days ago
-
RE: Mitsubishi Ecodan FTC6 settings
The Mitsi remote thermostat should not be plugged into ...
By F1p , 5 days ago
-
RE: PV and battery long payback - sense check query
@jamespa I was just commenting on the speed, not sug...
By Batpred , 5 days ago
SPONSORS
