Last seen: Jul 21, 2024
@djbuzz-07 Sunsynk Are you using lithium/ CAN protocol? If so, mine always starts grid charge @10% It is a setting on the inverter. Can...
Been quite a while since any update - but that's how long it's has taken to get to the root of the issue. Fogstar has owned up and finally ackno...
@robl I've added the screens. Li-Bms screen is accurate. Sunsynk screen shows a +0.3V difference between it and battery. Also shows voltage s...
@robl Ill take a photo of the screen tonight & also in AGMV mode - From memory, it is set to 56.7V - Unless i factory reset/run it in AGMV ...
@chickenbig Sunsynk support claims that Pylontech is not supported. Tho the BMS screen on the inverter is properly populated with the correct...
SITREP #5 No improvement on the system. Everyday, it is charging 1% less. Today was 84% then stopped charging. User timer set to 100%SOC. I'm ...
@misterb @vaugi OK, I'll contacted Fogstar Were I fall down that it is the battery - is that when the Sunsynk is factory reset - it charg...
@misterb @robl SITREP #4? Blimey, what haven't I tried Voltage mode, wasn't working very well. It's a bad SOC replacement. I tried every single...
Interesting review. Good timing for myself. Will be driving one shortly - how did you find space in the i4 - anyway bigger than expected?
SITREP #2 Progress, but not logical progress on the Sunsynk. So I changed the Sunsynk over to AGM-V Good - I was able to charge to 100% and...
Hey I ran active balancer for the first 3 cycles. Voltage on the screen looks in good shape per cell. Figuring out the Sunsynk however......
Ok, I have ths mode turned on. How did you know what voltages to set on the inverter?
Latest Posts
-
RE: Surface mount or bury primaries for heat pump installation?
@tomasmcguinness bold choice on the Kronoterm. Nice! Wi...
By Mars , 4 hours ago
-
RE: Getting the best out of a heat pump - is Homely a possible answer?
It took me more than a few goes as well, plus some help...
By cathodeRay , 21 hours ago
-
RE: Renewable Heating Hub Homeowners' Q&A Podcast
@ashp-bobba thank you, and equally so, thank you for ta...
By Mars , 1 day ago
-
@judith good to know… I’ll continue to feed Wattson, an...
By Mars , 2 days ago
-
RE: Vaillant AroTherm Plus 7kW
@jamespa I have a hydronic baseboard heater in the kitc...
By Scalextrix , 2 days ago
-
RE: My misgivings about installing ASHP and solar panels via the ECO4 scheme...
@editor great article re accreditation. I note ISO/IEC ...
By Bart , 2 days ago
-
RE: Renewables & Heat Pumps in the News
Here’s a little more technical detail/p>
By Judith , 3 days ago
-
RE: Who's your electricity provider and what's your tariff?
I don't (yet), but my PW3 is due to be installed shortl...
By Old_Scientist , 3 days ago
-
RE: MCS and NAPIT complaints process
@chrislay, is your heat pump complaint still unresolved...
By Mars , 3 days ago
-
RE: ASHP Install from hell - help please
@saf1973 I’ve been going through old cases on the forum...
By Mars , 3 days ago
-
RE: RDSAP10 effect on existing heat pump EPC rating?
@aaron There's the rub, the database does not list my ...
By AF1 , 4 days ago
-
RE: Commencing on an ASHP Installation Process
Yes, it's "doable" if everything goes to plan, they arr...
By Old_Scientist , 5 days ago
-
RE: How not to install a heat pump
You are right. Thinking on this has evolved over the p...
By JamesPa , 6 days ago
-
RE: DHW SET UP with Samsung gen 5
Thats good news indeed, you are very likely almost ther...
By JamesPa , 6 days ago
-
RE: Plate heat exchanger considerations
As far as I can tell my vented system would have a peak...
By Scalextrix , 6 days ago
-
RE: Air Changes per Hour - ACH and the MCS requirement
There have been a few discussions dotted around (e.g. I...
By Declan90 , 6 days ago
