Last seen: Nov 10, 2025
@bontwoody So Mark , once you have seen the new temps at tank , how does that work for you. Perhaps adjust the rads, or still work needed at buffer.
@bontwoody Hello , yes I maybe doing this wrong . I have two temp sensors on the pump lines next to the pumps I will move them to the buffer , and th...
@bontwoody I think I have just sent this in last post. The heating has just kicked in again 1 degree below setting , which is a tad slow in picking ...
@robl Yes very cold , 300mm all over , but not around tank area , cant feel much heat at all around tank area so all good. So , update , I have put ...
I have opened all the inlet valves on the Rads , about three were not fully open , but only about three , one turn. I have left the thermostat ends as...
Sorry "Insulation"
@bontwoody Yes , EPC was 2015 before HP was installed. I have sent a planof house layout and build descriptions , not an expert on details given , b...
Ordered probes. Did you get EPC report that gives the floor area and more .
I have two pics front and rear to hand, also think its a good idea to look at out going temps .I was looking at infra red but a bit confused , perhap...
So when you talk about the lockshield valve , is that the TRV on the entry side , I would have thought they are always wide open , unless you meed to ...
Many thanks, I haven't sent the Room radiator sizes , I thought I had. However I shall look at the various ways you have suggested . Iam already on...
The system I have in place seems to be adequate , other than tweeks with flow temp. Perhaps the tank can be taken out of the circuit then also . Many...
- 26 Forums
- 2,342 Topics
- 53 K Posts
- 187 Online
- 6,000 Members
Join Us!
Worth Watching
Latest Posts
-
RE: LiFePO4 lithium battery fires and explosions
That's somewhat of an understatement. 🤨 The ...
By Transparent , 2 hours ago
-
RE: Help me keep the faith with my air source heat pump installation
@simonf thats interesting as I’ve noticed my flow and r...
By AdamK , 3 hours ago
-
RE: MELcloud scheduling misbehaviour
No, it gets to set temperature easily even during perio...
By Abernyte , 4 hours ago
-
RE: Setback savings - fact or fiction?
@robs — is there anything weird in your post or footer/...
By cathodeRay , 4 hours ago
-
RE: Free Ecoheat Heat Pump Install
Sorry hit 'add reply' too early, this forum layout will...
By Deltona , 5 hours ago
-
RE: Poll for Time of Use, tariffs, technology
@batpred Fair enough, if the usage of these materials i...
By Papahuhu , 5 hours ago
-
And arguably even more important, sodium will be hopefu...
By Batpred , 8 hours ago
-
RE: A Smarter Smart Controller from Homely?
I've been thinking of emailing Homely to ask for a few ...
By JohnnyB , 20 hours ago
-
Max output of Heat pump (Daikin 4Kw EDLA04)
Hello, I am a bit puzzled that according to pcdb tes...
By GeorgeA , 20 hours ago
-
In that case, @technogeek, I’d sign up for the free sol...
By Majordennisbloodnok , 21 hours ago
-
RE: Has Anyone Else Noticed a Decline in Tradesmanship?
@cathoderay Hence my rider about ‘all else being equal’...
By Toodles , 22 hours ago
-
RE: Heat Pump Performance Analysis Web App using Modbus Data
@redzer_irl — all my heat pump data is in csv files, me...
By cathodeRay , 22 hours ago
-
That’s not a problem. If you can hit the main landing p...
By Majordennisbloodnok , 23 hours ago
-
RE: Configuration issues with 10kW Midea R32 heat pump
@benson I believe there are quite a few of these instal...
By Toodles , 23 hours ago
-
RE: 10kw heat pump run in 24*7 data?
I would say you most likely do need 10kW. My gas consu...
By JamesPa , 23 hours ago
-
RE: Mitsubishi Ecodan 11kw Defrosting Issue.
@thundermink I managed to find the fault. I did it a lo...
By meehow , 24 hours ago
-
RE: Here is my heat pump installation with questionable COP in Italy
Well in Italy there is nothing controlling the quality ...
By materox345 , 1 day ago
-
RE: What a Bad Heat Pump Installation Looks Like
@editor The trick to an inside unit installation is to ...
By MikeFl , 2 days ago


