Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jan 14, 2025
@betaphi not sure if anyone on here has the HT quiet, most are Gen6. two suggestions a) ask samsung (you can register on their partner portal pretty...
@redzer_irl I think I've just twigged what might have been wrong with version 1.0 of your design. you had it set to simply give a fixed LWT (which t...
@mike-h most of the modbus / make your own scheduling system discussion is in this thread
thats because the modbus / HA stuff is still at the experimental/tinkering stage, for people comfortable with coding etc. Not mature enough to be writ...
I and probably others would be really interested to hear how you get on . looking forward to the story!
In that situation, the flow temp follows the WL curve. The target room temp affects how long the system stays on, until that room temp is achieved. No...
but a somewhat oversized heat pump that is cycling in low demand, can also give a high COP, if everything else is done properly. Mine from this mornin...
preamble and system design: all good. same as mine give or take a few details. samsung wired remote as standalone controller - yes , if all you need...
it may be that your system is setup to always keep that buffer tank at the target LWT regardless of heat demand. Does it still keep the buffer tank wa...
so you definitely don't trust the nameplate number. you must read the spec sheets for the actual outputs. under vs over is more nuanced though. I ha...
there is a definitely a setting combination that gives you the samsung controller as the room temp stat, with WL. I am fairly sure its 2091 = 0 (becau...
Nice! monitor the flow rate via modbus, this will be the primary side. might be a tangential question, but why is the heat pump running when...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: The good, the bad and the not that great – my heat pump installation
@burtis, I’ve followed this thread pretty much from the...
By Mars , 2 hours ago
-
RE: Starting Our Heat Pump Journey: 1962 build 3 bed detached house
First time poster here but I can share my experience as...
By SCH , 8 hours ago
-
At the risk of going on: A slight side issue for a foru...
By Bart , 14 hours ago
-
RE: Is it the house or the equipment?
...which, I've found out, is pretty much impossible to ...
By Majordennisbloodnok , 15 hours ago
-
RE: Mitsubishi Ecodan FTC6 settings
The Mitsi remote thermostat should not be plugged into ...
By F1p , 1 day ago
-
RE: Do I add Air Con or MVHR to existing A2W ASHP?
@lizzie Thank you, very interesting and useful informat...
By Toodles , 1 day ago
-
RE: PV and battery long payback - sense check query
@jamespa I was just commenting on the speed, not sug...
By Batpred , 1 day ago
-
Readers here please note that Derril Water and many oth...
By Transparent , 2 days ago
-
RE: Advice on Vaillant Sensocomfort
Oops, I meant Sensocomfort (the UI to the controls)
By Batpred , 2 days ago
-
RE: Heat Pump Training vs. Real-World Installation
Our instal was very much the opposite. White haired blo...
By Batpred , 2 days ago
-
RE: Flushing system, cleaning and inhibitor
While skim reading a manual for our Vaillant HW tank, I...
By Batpred , 2 days ago
-
RE: 'Chinese Diesel Heater' to heat the home .....
Old thread but I'm new to the forum so new to me. How...
By BlizzardGreen , 2 days ago
-
I'm not sure why you would want to make it more difficu...
By JamesPa , 2 days ago
SPONSORS
