Last seen: Sep 19, 2024
The mixing valve arrangement, and the water pump above it, is as you say primarily for systems where the supplied water is above the temperature limi...
@jamespa The UFH mixing valves are shown in the final 2 photo's in the original post.
@ngillam Check the thermistor readings as detailed in the attached video. If the controller is indicating -39C then check to see if the control...
@iantelescope Thank you for providing the graph for sensor 1. Could you now please supply the graphs for sensor 3 and sensor 7 as requested. Ple...
@iantelescope How many radiators are on your system and are they all being heated?
Thank for supplying the model number for the energy meter. Could you please explain why you included the additional information that was not requeste...
@iantelescope Could you please confirm the model of Sharky that you have installed. I'm afraid that I am becoming confused by the multitude of gra...
@iantelescope Is the secondary water pump starting and stopping?
@iantelescope As an Instrumentation and Control System Engineer, the starting point is always to ensure that all sensors are correctly installed, th...
@toodles During a 24 hour period our baseload is in the 100W to 300W range with occasional dips below and surges above. Assuming a 200W / hr average...
@iantelescope Please explain what you mean by 'errors galore'. Please explain how you are monitoring and recording the various signals from the se...
@iantelescope Thank you for the Sharky readings, but could you please include the units and any decimal points. Please don't go off at a tangent o...
Latest Posts
-
RE: Surface mount or bury primaries for heat pump installation?
Current thinking is a Kronoterm Adapt. Doing the ground...
By tomasmcguinness , 2 hours ago
-
RE: Getting the best out of a heat pump - is Homely a possible answer?
It took me more than a few goes as well, plus some help...
By cathodeRay , 16 hours ago
-
RE: Renewable Heating Hub Homeowners' Q&A Podcast
@ashp-bobba thank you, and equally so, thank you for ta...
By Mars , 1 day ago
-
@judith good to know… I’ll continue to feed Wattson, an...
By Mars , 2 days ago
-
RE: Vaillant AroTherm Plus 7kW
@jamespa I have a hydronic baseboard heater in the kitc...
By Scalextrix , 2 days ago
-
RE: My misgivings about installing ASHP and solar panels via the ECO4 scheme...
@editor great article re accreditation. I note ISO/IEC ...
By Bart , 2 days ago
-
RE: Renewables & Heat Pumps in the News
Here’s a little more technical detail/p>
By Judith , 3 days ago
-
RE: Who's your electricity provider and what's your tariff?
I don't (yet), but my PW3 is due to be installed shortl...
By Old_Scientist , 3 days ago
-
RE: MCS and NAPIT complaints process
@chrislay, is your heat pump complaint still unresolved...
By Mars , 3 days ago
-
RE: ASHP Install from hell - help please
@saf1973 I’ve been going through old cases on the forum...
By Mars , 3 days ago
-
RE: RDSAP10 effect on existing heat pump EPC rating?
@aaron There's the rub, the database does not list my ...
By AF1 , 4 days ago
-
RE: Commencing on an ASHP Installation Process
Yes, it's "doable" if everything goes to plan, they arr...
By Old_Scientist , 5 days ago
-
RE: How not to install a heat pump
You are right. Thinking on this has evolved over the p...
By JamesPa , 6 days ago
-
RE: DHW SET UP with Samsung gen 5
Thats good news indeed, you are very likely almost ther...
By JamesPa , 6 days ago
-
RE: Plate heat exchanger considerations
As far as I can tell my vented system would have a peak...
By Scalextrix , 6 days ago
-
RE: Air Changes per Hour - ACH and the MCS requirement
There have been a few discussions dotted around (e.g. I...
By Declan90 , 6 days ago
