Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jun 19, 2026
I am still in discussions with the installer about installing FRVs. Had I known how accommodating they were I'd have done that before the LSVs were ...
Thanks @old_scientist I was going to turn TRVs down until I got the result I am looking, but your suggestion to start form zero is a much better id...
@jamespa Thankfully we'd already experienced chrome towel rails and the minimal output that comes from them and had already decided standard type 2...
When I saw the world flawless that immediately to me meant perfect. I was once told aiming for perfection is pretty much impossible, unachievable an...
Thanks @jamespa Yes, I'd be leaving several radiators fully open with no TRVs (all the downstairs ones) and 2 bathrooms as want the most heat in th...
@batpred The Pace BMS also isn't the best with it's balancing algorithm, along with most other BMS manufacturers. Only JK seem to have a handle o...
@batpred I'd change your JK balance start voltage a little lower to give a it a chance to actually balance your cells.
@batpred I would consider changing your balance start voltage a little lower to give the balancer a chance to do it's job.
As a side note I observed the the charge/discharge time window is 10 minutes out of sync. My Inverter is set to charge between 12.10am and 6.50am to...
@batpred As my battery packs were heavily used yesterday and had discharged to 20%, the charge window would mean they'd hit capacity around 6.30am ...
@batpred I reckon Andy might know a thing or 2 about this subject.
SPONSORS
Degrees of Separation
Latest Posts
-
@trebor12345 Try opening the settings window and then ‘...
By Toodles , 5 minutes ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
Individual room heat losses matter just as much as tota...
By cathodeRay , 13 minutes ago
-
Recommended flexi hoses for ASHP
I wonder if someone could recommend some high quality f...
By Old_Scientist , 9 hours ago
-
RE: Who's your electricity provider and what's your tariff?
@peterackstraw What's the calculated heat loss for your...
By ChandyKris , 10 hours ago
-
@editor — it was a not very well implemented so far as ...
By cathodeRay , 15 hours ago
-
RE: Microgeneration Certification Scheme (MCS)
@jamespa A cynical view but, I fear that it is a fair ...
By Toodles , 15 hours ago
-
RE: Jokes and fun posts about heat pumps and renewables
... except that the legal notice (part of which was rep...
By JamesPa , 16 hours ago
-
RE: Heat Pump Servicing & Maintenance – Good Value or Rip-Off?
@old_scientist if you are going DIY then you may wan...
By Papahuhu , 3 days ago
-
RE: Indevolt Batteries UK Support & Info Thread
After a short while that was followed by the 'power war...
By JamesPa , 3 days ago
-
RE: Samsung heat pump - data cable issue
That's well done. Cable is the correct type (LIYCY = 2x...
By bobflux , 3 days ago
-
RE: Electricity price predictions
I agree, we will find out at the next budget whether th...
By Old_Scientist , 3 days ago
-
RE: Missing flow temperature in Heat Geek proposal
@editor I went through HG website, so should be ok for ...
By sttpd1917 , 4 days ago
-
RE: Air to air bus grant installer anywhere
The through wall two hole ones have their place (listed...
By EtchedPixels , 4 days ago
-
I hope it goes ok, Hon can be hard to set up IF the sof...
By Graham Hendra , 4 days ago
-
@clockworks Hi, So there is a big difference between st...
By ASHP-BOBBA , 4 days ago
SPONSORS
