Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Mar 20, 2026
Good day all. Questions on heating using fan coils: 1. can one use weather compensation with fan coils ? 2. Do fan coils require higher water ...
@grantmethestrength OK, thanks, I don't use HA, I have written my own interface in MATLAB, if you know.
@grantmethestrength What are "blueprints" please ?
@cathoderay what is the setting for room thermostat ? (bottom lines of 1st page of instructions)
@cathoderay well exactly because it says so on the screen. Furthermore, the fact that curve 9 is shown as selected does not mean it is in effect. I ag...
@cathoderay I am pretty sure your unit is set to operate on "Water temperature control" and not on WCC control.
@cathoderay Are you using Midea's wired controller to operate the heat pump or some other method (modbus or whatever). Furthermore, even with a fixe...
@cathoderay I tend to agree with Mk4. Why don't you try his suggestions and see what happens.
In my controller, this can be done in service menu: Also noted:
@cathoderay I think the 45 C is the set LWT if you operate on LWT control, not the LWT calculated from the WCC. Further, IAT set-point, defined at t...
I confirm system shutting down after exiting the SERVICEMAN MODE but not shutting down when parameters changed through direct modbus communication. ...
I have not noticed something of that sort but I will check tomorrow to be sure.
SPONSORS
Degrees of Separation
Latest Posts
-
-
RE: Who's your electricity provider and what's your tariff?
Many thanks. Good info
By peterackstraw , 1 hour ago
-
@editor — it was a not very well implemented so far as ...
By cathodeRay , 2 hours ago
-
RE: Microgeneration Certification Scheme (MCS)
@jamespa A cynical view but, I fear that it is a fair ...
By Toodles , 2 hours ago
-
RE: Jokes and fun posts about heat pumps and renewables
... except that the legal notice (part of which was rep...
By JamesPa , 2 hours ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
Have either quote provided room by room heat loss calcu...
By Old_Scientist , 23 hours ago
-
RE: Heat Pump Servicing & Maintenance – Good Value or Rip-Off?
@old_scientist if you are going DIY then you may wan...
By Papahuhu , 2 days ago
-
RE: Indevolt Batteries UK Support & Info Thread
After a short while that was followed by the 'power war...
By JamesPa , 2 days ago
-
RE: Samsung heat pump - data cable issue
That's well done. Cable is the correct type (LIYCY = 2x...
By bobflux , 3 days ago
-
RE: Electricity price predictions
I agree, we will find out at the next budget whether th...
By Old_Scientist , 3 days ago
-
RE: Missing flow temperature in Heat Geek proposal
@editor I went through HG website, so should be ok for ...
By sttpd1917 , 3 days ago
-
RE: Air to air bus grant installer anywhere
The through wall two hole ones have their place (listed...
By EtchedPixels , 3 days ago
-
I hope it goes ok, Hon can be hard to set up IF the sof...
By Graham Hendra , 3 days ago
-
@clockworks Hi, So there is a big difference between st...
By ASHP-BOBBA , 3 days ago
-
@editor wellvery comprehensive answer. I will get all i...
By Keithb , 3 days ago
SPONSORS
