Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Aug 13, 2026
@derek-m thanks for the information Derek…. There’s a lot of data in your post to digest. By way of interim feedback, we have been running our sY...
How are people using the Mitsubishi wireless remote. I’ve only used it with Auto Adaptive / room temperature mode. As a target room temperature contro...
indeed this is part of the conundrum But I think Auto Adapt, and it’s tendency to overshoot then cool back is also part of the same problem. You may r...
@derek-m hi Derek, The points you raise are all very valid and ones we’ve been becoming familiar with. We are all too familiar with understand...
I don’t think your first assumption is having an effect on the end of the day. But I can confirm your second point. The radiators were fully heated at...
Answers to the quiz: Low flow rate vs high flow rate. The 11 o’clock graph is operating at 19lpm and the 12 o’clock and 15 o’clock graphs were opera...
Thats interesting… I haven’t seen such super high temps. I’ve never thought of containing the upper temperature limit. I have mine set to 53c because ...
hi @gotaashp I was interested in your 24 hour room temp graph which shows how AUTO ADAPT tries to anticipate and over run set temperatures. Its i...
Hi Walker, Thanks for your thoughts. The good news about the rating of Ecodan is that the output range of the compressor is quite a bit higher than...
Here is a challenge for you Derek: One of these graphs is recorded during a flow rate of 19lpm and 2 of the graphs are recorded at a flow rate of 14...
Thanks that sounds interesting Kev Meanwhile, I’ve changed to WC curve it is set at 31c at today’s outside temperature of 8c. So I’ve added +2 to b...
hi, I’m pretty sure it’s no coincidence. Earlier in the month I was getting 20 minutes cycling but, like you, I also had the period set to 20 minutes....
SPONSORS
Degrees of Separation
Latest Posts
-
RE: 7kW EV Charger Options Advice
I was hoping that the electrician would route the under...
By Rusty , 9 hours ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
@jamespa @transparent Sorry about that. Here are the ch...
By jon , 9 hours ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@tim441 Yes, I too am waiting for V2H before I get an E...
By Papahuhu , 11 hours ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
Post by: @old_scientist The first thing I would say ...
By Rob of York , 13 hours ago
-
RE: Adding additional Solar Panels to a DC coupled battery system
@transparent thank you for your reply above. As alway...
By Old_Scientist , 19 hours ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@kilgorexv definitely a larger inverter will help and m...
By AndrewJ , 2 days ago
-
RE: Adventures in heat loss calculations
@rob-of-york — thanks for posting this, all very useful...
By cathodeRay , 3 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
The installation is almost done! I've written up two ...
By tomasmcguinness , 3 days ago
-
RE: Glass lined Cylinder for private water supply
This has turned into a fascinating little rabbit hole. ...
By Mars , 3 days ago
-
RE: Switch suitable to change between two inverter CT's
Last winter my battery ,32KWh, could run the house com...
By Jancold , 3 days ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
Agree with Major. And even if I was very happy with ...
By Batpred , 3 days ago
-
RE: Is the "divide by 2900" rule still valid?
There is another estimator that you could use, a formul...
By Rob of York , 4 days ago
-
RE: To re-pipe or not to re-pipe? Moving from oil boiler to air source heat pump.
@penval, really useful update. After all the discussion...
By Mars , 6 days ago
-
RE: Who's your electricity provider and what's your tariff?
@papahuhu I prefer to look at it simplistically. We d...
By Old_Scientist , 7 days ago
SPONSORS
