Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jan 5, 2026
@transparent oh yeah i get you now, the flow wasnt for loops just o keep stuff from freezing, do ye mean antifreeze in ufh water thats going to loops ...
@transparent actually missed that graph was freezing, was only looking around 4am. hopefully so by changing setting to minus 4 it wont kick in. Though...
@transparent Would it just have the 1 sensor that gives me my digital reading on main screen because that said something like2degrees at 5am.
It wasn't below freezing last night, some sensor must be off, where would best place to check be? I doubt buh is even mean to come on if it just goes ...
@transparent yeah might do that, where would i put it on daikin unit?
@derek-m cant see label but shur it must have been added, had no problems during winter. Changed equilibrium temp of building to -4. Just looking at a...
@derek-m cheers man. No wasnt freezing this morning at 4am, was approx 2 degrees on panel, i was half asleep looking at it though, this i dont think h...
@transparent yeah its just annoying at this stage, maybe just disable buh, if derek m recommends that.
has enable buh step 2 - yes
@transparent reading from main screen on front of unit panel. Reads 48 just after heatup so thinkits accurate.
@derek-m it is enabled, dont think it says anything about temp. equilibrium temp 0deg it says in settings.
@derek-m says capacity of backup heater @: t design -10deg 9kw
- 26 Forums
- 2,726 Topics
- 63.8 K Posts
- 2,340 Online
- 7,126 Members
Join Us!
Installer Finder
Degrees of Separation
Latest Posts
-
Recommended flexi hoses for ASHP
I wonder if someone could recommend some high quality f...
By Old_Scientist , 8 hours ago
-
RE: Who's your electricity provider and what's your tariff?
@peterackstraw What's the calculated heat loss for your...
By ChandyKris , 9 hours ago
-
@trebor12345 20% does sound excessive. Gemini suggests ...
By ChandyKris , 9 hours ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
If you know the room heat losses for each of the rooms ...
By Temperature_Gradient , 11 hours ago
-
@editor — it was a not very well implemented so far as ...
By cathodeRay , 14 hours ago
-
RE: Microgeneration Certification Scheme (MCS)
@jamespa A cynical view but, I fear that it is a fair ...
By Toodles , 14 hours ago
-
RE: Jokes and fun posts about heat pumps and renewables
... except that the legal notice (part of which was rep...
By JamesPa , 14 hours ago
-
RE: Heat Pump Servicing & Maintenance – Good Value or Rip-Off?
@old_scientist if you are going DIY then you may wan...
By Papahuhu , 3 days ago
-
RE: Indevolt Batteries UK Support & Info Thread
After a short while that was followed by the 'power war...
By JamesPa , 3 days ago
-
RE: Samsung heat pump - data cable issue
That's well done. Cable is the correct type (LIYCY = 2x...
By bobflux , 3 days ago
-
RE: Electricity price predictions
I agree, we will find out at the next budget whether th...
By Old_Scientist , 3 days ago
-
RE: Missing flow temperature in Heat Geek proposal
@editor I went through HG website, so should be ok for ...
By sttpd1917 , 3 days ago
-
RE: Air to air bus grant installer anywhere
The through wall two hole ones have their place (listed...
By EtchedPixels , 4 days ago
-
I hope it goes ok, Hon can be hard to set up IF the sof...
By Graham Hendra , 4 days ago
-
@clockworks Hi, So there is a big difference between st...
By ASHP-BOBBA , 4 days ago



