Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jan 14, 2025
@william1066 I think you've misread the diagram. you read across at 1 l/sec and select any kvs line within the shaded area. My purple line. higher k...
@cathoderay esphome can run with encryption. default is non encrypted but its just a config option. wifi, I get it, it does depend on the quality o...
@william1066 I'm exactly same as you. keen DIYer' . I'd prefer it if the filters came with 28mm connections, but those are all too small bore inside. ...
@cathoderay there are different ways to physically do this: it depends on what is where. you need something that is basically a PC (a large one, a s...
@william1066 3.6m3/h with a DP of 0.22mh20 means its not relying on a monster pump. the chart is here I was comparing to some of the usual suspect ...
@william1066 doing some component research over the weekend. spirotech 1 1/4 " pressure loss spec took some hunting down but its 2.2kpa (0.22 m...
@katcesca you've missed something. you do not need to have an EV to access TOU tariffs like octopus Go (12p/unit 4hr offpeak) - despite what some of t...
TLDR: I nearly fell off my chair when I saw your cost for radiators and fittings. That said, it matches with the ballpark that a number of "ASHP com...
thats exactly what I've done already. This pushes air through the center of a slightly undersized radiator and makes a noticeable difference to its ou...
@heacol so if I'm going to replumb in a couple of weeks will you be selling by that point, or just get a bellimo from JTM?
@william1066 are saying you able to adjust the HP's target DT directly on the samsung? If as per the OP, you knew your system wasn't able to cope wi...
@william1066 I think the bellimo valves that @heacol recommends are back in stock at JTM, I'm tempted to grab one for my build before he gets them all...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Do I add Air Con or MVHR to existing A2W ASHP?
Cloudy one done, might get the sunny one tomorrow or de...
By Watcher , 7 hours ago
-
RE: The good, the bad and the not that great – my heat pump installation
@burtis, I’ve followed this thread pretty much from the...
By Mars , 1 day ago
-
RE: Starting Our Heat Pump Journey: 1962 build 3 bed detached house
First time poster here but I can share my experience as...
By SCH , 1 day ago
-
At the risk of going on: A slight side issue for a foru...
By Bart , 2 days ago
-
RE: Is it the house or the equipment?
...which, I've found out, is pretty much impossible to ...
By Majordennisbloodnok , 2 days ago
-
RE: Mitsubishi Ecodan FTC6 settings
The Mitsi remote thermostat should not be plugged into ...
By F1p , 2 days ago
-
RE: PV and battery long payback - sense check query
@jamespa I was just commenting on the speed, not sug...
By Batpred , 2 days ago
-
Readers here please note that Derril Water and many oth...
By Transparent , 2 days ago
-
RE: Advice on Vaillant Sensocomfort
Oops, I meant Sensocomfort (the UI to the controls)
By Batpred , 2 days ago
-
RE: Heat Pump Training vs. Real-World Installation
Our instal was very much the opposite. White haired blo...
By Batpred , 2 days ago
-
RE: Flushing system, cleaning and inhibitor
While skim reading a manual for our Vaillant HW tank, I...
By Batpred , 3 days ago
-
RE: 'Chinese Diesel Heater' to heat the home .....
Old thread but I'm new to the forum so new to me. How...
By BlizzardGreen , 3 days ago
SPONSORS
