Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jan 14, 2025
@tomasmcguinness I did my own, all of it bar the electrics. If you are a competent DIY plumber , and take the time to read lots of design advice, i...
if you are using the samsung controller as the roomstat, and by setback you mean that you want to alter the target room temperature at a specific tim...
This could be your smoking gun. Its a preset, lower value restricts flow more. so even with the TRV head set to max (or removed), it'll never let thro...
@crimson IR stuff - I have a basic IR spot gun which isn't bad for not much money and is quick and easy. But I eventually I got a Seek Thermal for my ...
exactly that. If you find that with the ASHP heating on, and a 400W of direct electric heat as well (whether that is one 400w heater on all the time, ...
@crimson I was thinking something like this,at lowest power 750w, or thisat lowest power 400W. Both are dirt cheap, lightweight and small, and afterwa...
@crimson your summary is pretty much spot on. something just occurred to me - if you ran a cheapo electric convector heater in your underheated room...
@crimson another sanity check, are you sure that UP/DOWN/UFH are correctly identified on those 3 valves? I do take your point that you think upstair...
@crimson gnaaah, just noticed you've got a bypass as well. In the high head loss situation you are trying to balance against, the bypass will probably...
@crimson so the downstairs is a honeywell V4043H1056 which has a KVS of 6.9 . the other two are EPH controls V222P with a KVS of 4.6. KVS is the expec...
@crimson remind your builder this is 22mm plastic, which is almost equivalent to 15mm copper in bore size. if you ask him "would you have done it in 1...
@crimson just a sanity check. have you swapped your probes around to check that the temp differences seen are not due to calibration variation.
SPONSORS
Degrees of Separation
Latest Posts
-
All I have in Utility Rate Plan is the 2 tariffs that I...
By trebor12345 , 26 minutes ago
-
RE: Indevolt Batteries UK Support & Info Thread
I profoundly disagree, but it is of course use case dep...
By JamesPa , 40 minutes ago
-
@grahamh-energy-donkey — thanks for the clarifications....
By cathodeRay , 2 hours ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
A good analysis with which I agree
By JamesPa , 18 hours ago
-
RE: Jokes and fun posts about heat pumps and renewables
@majordennisbloodnok Well, I can use such terms as HMRC...
By Toodles , 19 hours ago
-
RE: Heat Pump Servicing & Maintenance – Good Value or Rip-Off?
I'd picked up that there was a leak coming from around ...
By Sheriff Fatman , 23 hours ago
-
RE: Who's your electricity provider and what's your tariff?
Great info. Thank you. Regards Pete
By peterackstraw , 23 hours ago
-
-
RE: Microgeneration Certification Scheme (MCS)
@jamespa A cynical view but, I fear that it is a fair ...
By Toodles , 2 days ago
-
RE: Samsung heat pump - data cable issue
That's well done. Cable is the correct type (LIYCY = 2x...
By bobflux , 4 days ago
-
RE: Electricity price predictions
I agree, we will find out at the next budget whether th...
By Old_Scientist , 5 days ago
-
RE: Missing flow temperature in Heat Geek proposal
@editor I went through HG website, so should be ok for ...
By sttpd1917 , 5 days ago
-
RE: Air to air bus grant installer anywhere
The through wall two hole ones have their place (listed...
By EtchedPixels , 5 days ago
-
I hope it goes ok, Hon can be hard to set up IF the sof...
By Graham Hendra , 5 days ago
SPONSORS
