Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Sep 1, 2026
I don’t know about the immersion settings to be honest as I’ve never used them. Regarding the limits I thought that this unit could go up to 60 LWT ...
Ah ok. There's obviously different schools of thought with respect to the benefits of disinfect cycles but guess you have probably done your own resea...
@painter26 welcome to the forum. However, I don't really get what you are trying to do with your DHW- why are you trying to heat the cylinder so high?...
There is a workaround for this that another forum member signposted me to recently- put heating zone in UFH mode.
@tasos the graph above from around 2100hrs shows the longest space heating run I'm going to have a plot for, without a DHW reheat. This is when LWT se...
@odd_lion the minimum MCS requirement is 2.8. I don't think installers are going to challenge homely on it. Why would they? Your differential betw...
@tasos as above the pump is always running... Thanks for the suggestion regarding the workaround to lower the set outlet flow temps below 35°C by ch...
Same experience with our midea and homely. Homely would overestimate COP by a fair bit compared with the wired controller readings. The very controlle...
I have found the setting which changes from rads to UFH so that looks like a good workaround if I need it. That said, coasting nicely at 35°C LWT pres...
@tasos interesting. I might look into that. My other option is just to use our indoor temp sensor to turn the ashp off when it gets milder and when a ...
@cathoderay I'm not quite sure I can do that with my setup in terms of looking at the address registers? The svenar device will just provide me all of...
I just realised that there is another setting I need to change but this is not one I can change via modbus- temperature lower limit of T1S heating zon...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Who's your electricity provider and what's your tariff?
@jamespa There is so much complexity in the world that ...
By Papahuhu , 32 minutes ago
-
RE: Missing flow temperature in Heat Geek proposal
The Heat geek contract had various get-out clauses with...
By Batpred , 1 hour ago
-
RE: Why are ASHP installs so expensive?
It seems a quite comprehensive breakdown. I will try to...
By Batpred , 2 hours ago
-
Thanks @jamespa The gas fire is definitely not an ess...
By Rob of York , 3 hours ago
-
RE: Starting Our Heat Pump Journey: 1962 build 3 bed detached house
@ian-s I would encourage you to have a conversation ...
By Rob of York , 7 hours ago
-
RE: Is it the house or the equipment?
Thanks @jamespa The last hard to fix draughts in the...
By springswood , 9 hours ago
-
RE: Vaillant Arotherm – Using Heating
@l8again Mine is typically using 11w including the i...
By Batpred , 11 hours ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
If you have a flowmeter and two temperature probes, the...
By bobflux , 19 hours ago
-
RE: Siting of the external sensor on a heatpump
@jamespa Absolutely. Even if the same mistake was mad...
By Batpred , 1 day ago
-
-
RE: Recommendations in Ely (Cambs) area for Full setup checks on Nibe HP setup for House.
In fairness all heating has cost a lot to run in recent...
By JamesPa , 2 days ago
-
RE: Navigating the World of Refrigerants In Heat Pumps: A Guide for Homeowners
Indeed we are invvestigating AC at present and are havi...
By Toodles , 3 days ago
-
RE: Daikin ESPAltherma and Home Assistant installation
It's laziness lol The PV system is very chatty, meter...
By bobflux , 4 days ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
R (The R Project for Statistical Computing, I use it wi...
By cathodeRay , 4 days ago
SPONSORS
