Forums

Forums
Renewable Heating
Air Source Heat Pum...
Removing a Low Loss...
 
Notifications
Clear all

Removing a Low Loss Header from Samsung Gen6 System

 
Page 2 / 3
Air Source Heat Pumps (ASHPs)
Last Post by bontwoody 1 year ago
28 Posts
5 Users
0 Reactions
3,947 Views
RSS
bontwoody
 bontwoody
(@bontwoody)
Noble Member Contributor
Joined: 4 years ago
Posts: 850
01/04/2024 5:23 pm  

@ecobaker Thats correct, I made the mistake of getting the same pump, but then decided to to sell it on ebay and get the UPM3 FLEX AS 25-75 130 AZA also on ebay.


House-2 bed partial stone bungalow, 5kW Samsung Gen 6 ASHP (Self install)
6.9 kWp of PV
5kWh DC coupled battery
Blog: https://thegreeningofrosecottage.weebly.com/
Heatpump Stats: http://heatpumpmonitor.org/system/view?id=60


   
ReplyQuote
 HughF
(@hughf)
Noble Member Member
Joined: 3 years ago
Posts: 489
01/04/2024 5:23 pm  

@heacol easily resolved with a jumper wire on the end of the flow sensor cable 🤣

When I was commissioning my Sprsun I could not get the air out, kept tripping on a flow sensor issue. Jumpered the flow sensor out and left it at that. Haven’t seen a flow error since then 🤣 Got the air out eventually.


Off grid on the isle of purbeck
2.4kW solar, 15kWh Seplos Mason, Outback power systems 3kW inverter/charger, solid fuel heating with air/air for shoulder months, 10 acres of heathland/woods.

My wife’s house: 1946 3 bed end of terrace in Somerset, ASHP with rads + UFH, triple glazed, retrofit IWI in troublesome rooms, small rear extension.


   
ReplyQuote
bontwoody
 bontwoody
(@bontwoody)
Noble Member Contributor
Joined: 4 years ago
Posts: 850
01/04/2024 5:25 pm  

@heacol 👍


House-2 bed partial stone bungalow, 5kW Samsung Gen 6 ASHP (Self install)
6.9 kWp of PV
5kWh DC coupled battery
Blog: https://thegreeningofrosecottage.weebly.com/
Heatpump Stats: http://heatpumpmonitor.org/system/view?id=60


   
ReplyQuote



 EcoBaker
(@ecobaker)
Estimable Member Member
Joined: 1 year ago
Posts: 44
Topic starter 01/04/2024 5:42 pm  

If the HP can't modulate below flow temp of 45 degrees and I'm aiming for flow temps of 35, is there much point in swapping out for a different pump?


Samsung Gen6 8kw ASHP in a two bed victorian mid terrace.


   
ReplyQuote
 Brendon Uys
(@heacol)
Noble Member Contributor
Joined: 4 years ago
Posts: 408
01/04/2024 5:43 pm  

@ecobaker probably not


Director at Heacol | Expert Heat Pump Consultant | Book a one-to-one consultation for pre- and post-installation advice, troubleshooting and system optimisation.


   
ReplyQuote
bontwoody
 bontwoody
(@bontwoody)
Noble Member Contributor
Joined: 4 years ago
Posts: 850
01/04/2024 5:46 pm  

@ecobaker Probably not if the unit cant modulate at 35C. Maybe @Iancalderbank can advise if it works as low as that as i havent run mine that low yet.


House-2 bed partial stone bungalow, 5kW Samsung Gen 6 ASHP (Self install)
6.9 kWp of PV
5kWh DC coupled battery
Blog: https://thegreeningofrosecottage.weebly.com/
Heatpump Stats: http://heatpumpmonitor.org/system/view?id=60


   
ReplyQuote
bontwoody
 bontwoody
(@bontwoody)
Noble Member Contributor
Joined: 4 years ago
Posts: 850
02/04/2024 1:33 pm  

@ecobaker @heacol 

I managed to talk to Glyn Hudson who was having difficulties getting PWM to work with his Samsung. However he has managed to sort it with a firmware update of the indoor controller and now it works at low flow temperatures, so it seems Samsung have sorted it.

https://community.openenergymonitor.org/t/samsung-mim-c02n-s-net-pro-dongle/25418/5

unnamed

House-2 bed partial stone bungalow, 5kW Samsung Gen 6 ASHP (Self install)
6.9 kWp of PV
5kWh DC coupled battery
Blog: https://thegreeningofrosecottage.weebly.com/
Heatpump Stats: http://heatpumpmonitor.org/system/view?id=60


   
ReplyQuote
 iancalderbank
(@iancalderbank)
Noble Member Contributor
Joined: 3 years ago
Posts: 643
02/04/2024 6:45 pm  

@bontwoody it will run at 35, but only stably if you have enough emitters  to balance the min output of the HP. Which in my case with a 16kw gen6 unit is 3.5kw. Below about 34-35C my emitter output drops too low , so it would short cycles , so I have tuned the WC so it doesn't go much below that.

lots of run data on my heatpumpmonitor.org data, as per my sig.


My octopus signup link https://share.octopus.energy/ebony-deer-230
210m2 house, Samsung 16kw Gen6 ASHP Self installed: Single circulation loop , PWM modulating pump.
My public ASHP stats: https://heatpumpmonitor.org/system/view?id=45
11.9kWp of PV
41kWh of Battery storage (3x Powerwall 2)
2x BEVs


   
ReplyQuote
bontwoody
 bontwoody
(@bontwoody)
Noble Member Contributor
Joined: 4 years ago
Posts: 850
02/04/2024 9:03 pm  

@iancalderbank Thanks Ian.


House-2 bed partial stone bungalow, 5kW Samsung Gen 6 ASHP (Self install)
6.9 kWp of PV
5kWh DC coupled battery
Blog: https://thegreeningofrosecottage.weebly.com/
Heatpump Stats: http://heatpumpmonitor.org/system/view?id=60


   
ReplyQuote



 EcoBaker
(@ecobaker)
Estimable Member Member
Joined: 1 year ago
Posts: 44
Topic starter 05/04/2024 10:05 am  

@bontwoody @iancalderbank Thanks for the advice. Looks like Ill try and get a firmware update before removing the LLH, although that could be tricky.

Also I just swapped out a small radiator for a much bigger one in my kitchen which resulted in a jump of daily COP from 3.6 to 4.1, I have three other rads I want to swap as well when I can afford to do it. I think thats probably a first step before removing a LLH or changing pump. 


Samsung Gen6 8kw ASHP in a two bed victorian mid terrace.


   
ReplyQuote
 iancalderbank
(@iancalderbank)
Noble Member Contributor
Joined: 3 years ago
Posts: 643
05/04/2024 10:20 am  

@ecobaker mine did not need a firmware change. the PWM worked first time. I am not even sure how you would go about getting a firmware change done.

radiator changes - yes - put your effort in there first. obvious gains as you have found.


My octopus signup link https://share.octopus.energy/ebony-deer-230
210m2 house, Samsung 16kw Gen6 ASHP Self installed: Single circulation loop , PWM modulating pump.
My public ASHP stats: https://heatpumpmonitor.org/system/view?id=45
11.9kWp of PV
41kWh of Battery storage (3x Powerwall 2)
2x BEVs


   
ReplyQuote
bontwoody
 bontwoody
(@bontwoody)
Noble Member Contributor
Joined: 4 years ago
Posts: 850
05/04/2024 10:27 am  

@ecobaker 

definitely. Bigger rads and lower flow temperature is your low hanging fruit. 


House-2 bed partial stone bungalow, 5kW Samsung Gen 6 ASHP (Self install)
6.9 kWp of PV
5kWh DC coupled battery
Blog: https://thegreeningofrosecottage.weebly.com/
Heatpump Stats: http://heatpumpmonitor.org/system/view?id=60


   
ReplyQuote
Page 2 / 3
Forum Jump:
  Previous Topic
Next Topic  
Topic Tags:  headers (1) ,



Share:

Join Us!

Podcast Picks

Latest Posts

Members Online

Click to access the login or register cheese
x Powerful Protection for WordPress, from Shield Security
This Site Is Protected By
ShieldPRO →