Last seen: May 5, 2025
Amazon just delivered, some good content, but the typesetting and layout needs a bit of work if there's a second revision planned.
Always go with the manufacturers controls/stats (if you must have a stat - ideally you don't need one)
Purchased.... although from Amazon as I've been rushing around like a lunatic all weekend and Amazon was a couple of finger clicks and I pay for Prime...
Homely is a smart thermostat that is specifically designed for ASHP use. It provides full, advanced, weather comp and scheduling from a smart phone ap...
The design is more important than the unit, unless you want to take advantage of the manufacturers specific controls as opposed to a simple on/off sta...
Take the buffer out, split the two systems into upstairs and downstairs. Set the weather comp curves for the upstairs rads to suit, and the same for t...
Who was your system designer, just so I know who to avoid 🙂 That ufh manifold needs a mixer, I genuinely don’t get why these installers think o...
I went to talk installation specifics with Cool Energy (a brand I can afford), and to look at/prod as many controllers as possible to assess the HMI f...
Everyone was there (except Freedom/Midea). Mitsubishi had their own booth, Unitherm had a multi-brand booth showing Samsung and LG units. Grant were t...
Sorry, not quite sure what you mean by this question? Is it relating to where the funds come from to operate the MCS scheme?
@derek-m Because they don't actually understand the science behind how these things work and try and set them up like a boiler. They expect the manufa...
DIY installation of a monoblock really couldn't be simpler - 28mm to a 3 port diverter, one side to your heating, the other to your cylinder coil or s...
Latest Posts
-
RE: Vaillant AroTherm Plus 7kW
@scalextrix if your under unit heater is like our Myson...
By Judith , 57 minutes ago
-
RE: Getting the best out of a heat pump - is Homely a possible answer?
@cathoderay how did you get a script to run for that- d...
By benson , 2 hours ago
-
RE: Surface mount or bury primaries for heat pump installation?
@tomasmcguinness bold choice on the Kronoterm. Nice! Wi...
By Mars , 8 hours ago
-
RE: Renewable Heating Hub Homeowners' Q&A Podcast
@ashp-bobba thank you, and equally so, thank you for ta...
By Mars , 1 day ago
-
@judith good to know… I’ll continue to feed Wattson, an...
By Mars , 2 days ago
-
RE: My misgivings about installing ASHP and solar panels via the ECO4 scheme...
@editor great article re accreditation. I note ISO/IEC ...
By Bart , 3 days ago
-
RE: Renewables & Heat Pumps in the News
Here’s a little more technical detail/p>
By Judith , 3 days ago
-
RE: Who's your electricity provider and what's your tariff?
I don't (yet), but my PW3 is due to be installed shortl...
By Old_Scientist , 3 days ago
-
RE: MCS and NAPIT complaints process
@chrislay, is your heat pump complaint still unresolved...
By Mars , 3 days ago
-
RE: ASHP Install from hell - help please
@saf1973 I’ve been going through old cases on the forum...
By Mars , 3 days ago
-
RE: RDSAP10 effect on existing heat pump EPC rating?
@aaron There's the rub, the database does not list my ...
By AF1 , 4 days ago
-
RE: Commencing on an ASHP Installation Process
Yes, it's "doable" if everything goes to plan, they arr...
By Old_Scientist , 5 days ago
-
RE: How not to install a heat pump
You are right. Thinking on this has evolved over the p...
By JamesPa , 6 days ago
-
RE: DHW SET UP with Samsung gen 5
Thats good news indeed, you are very likely almost ther...
By JamesPa , 6 days ago
-
RE: Plate heat exchanger considerations
As far as I can tell my vented system would have a peak...
By Scalextrix , 6 days ago
-
RE: Air Changes per Hour - ACH and the MCS requirement
There have been a few discussions dotted around (e.g. I...
By Declan90 , 6 days ago
