Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jul 31, 2026
i think its hilarious that our industry worries about cop when all that matters is run cost. The pumps are there to do a job, they would be there if y...
@olly there is a technical issue with it not being on the mcs yet, i think its supposed to be on in December, after that reviews will pour in. But fro...
and that explains why i have a job, i spend my days speaking to homeowners after they have had a site visit from thier installer of choice and have lo...
I wrote a book answering all these questions its on amazon, but why on earth would you buy a unit from someone who cant answer the qs? , getting idiot...
@mars i would but its not in yet, samsung are waiting for mcs at the ned of the month, then mine arrives, but ive seen it and its lovely.
it will be mcs soon, i would wait, its miles better than the gen 6,
if you have a midea samsung or hitachi heat pumps i have done videos how to adjust your weather comp.hope they help
all seems resonable to me, i would use allh because the pi runs are long, burying the pipe use rauvitherm pipe in pipe, its very expensive but brillia...
all heat pumps work at 5 degree delta t, so you can only squeeze 10kW down it. its q 68 in book 2 .
Good points but if flow is restricted the pump is flat out and compressor slows, if there is spare pump capacity (very rare) what you say is true. the...
@editor dont worry to much about it, its just maths, if the delta t is 5 degrees and the flow rate is 30l/ min you are going to be able to deliver 10k...
@jeff no it doesn't stop working, it will fight you, its whole mission is to make a 5 degree delta t so it will slow the compressor therefore output k...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Being screwed over by Volkswagen Audi Group
VW, Audi, Seat/Cupra and Skoda all use the same IT infr...
By Majordennisbloodnok , 3 hours ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
A calibrated heat meter is an option, it is not cheap, ...
By bobflux , 4 hours ago
-
RE: 7kW EV Charger Options Advice
Thank you Rusty, all of those subtleties were lost on m...
By Judith , 5 hours ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
Flow rate is set by pressure created by the circulator ...
By bobflux , 22 hours ago
-
RE: Glass lined Cylinder for private water supply
I have one of those... a Thermal Store. In my case th...
By Transparent , 1 day ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@tim441 Here are those same three month periods for 202...
By Toodles , 1 day ago
-
RE: Adding additional Solar Panels to a DC coupled battery system
@transparent thank you for your reply above. As alway...
By Old_Scientist , 2 days ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@kilgorexv definitely a larger inverter will help and m...
By AndrewJ , 4 days ago
-
RE: Adventures in heat loss calculations
@rob-of-york — thanks for posting this, all very useful...
By cathodeRay , 4 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
The installation is almost done! I've written up two ...
By tomasmcguinness , 4 days ago
-
RE: Switch suitable to change between two inverter CT's
Last winter my battery ,32KWh, could run the house com...
By Jancold , 5 days ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
Agree with Major. And even if I was very happy with ...
By Batpred , 5 days ago
-
RE: Is the "divide by 2900" rule still valid?
There is another estimator that you could use, a formul...
By Rob of York , 5 days ago
-
RE: To re-pipe or not to re-pipe? Moving from oil boiler to air source heat pump.
@penval, really useful update. After all the discussion...
By Mars , 1 week ago
SPONSORS
