Forums

Forums
Members
Gary
Activity
 
Notifications
Clear all
Gary
@gary
Member
Prominent Member
Joined: Feb 8, 2023
Last seen: Aug 13, 2025
Profile Activity
Topics: 2 / Replies: 348
AllTopicsReplies
Reply
RE: hum/whine from Wilo circulation pump

From your quote here I understood that the heat pump wasn't operating at night as you have the house quite cool. In the documentation you got from yo...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: hum/whine from Wilo circulation pump

@grumpidoc do you have glycol in your system if so you can deactivate the frost protection mode so the pumps won't activate at night.

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Mitsubishi Ecodan stuck on immersion symbol

Ideally you want it all to come on at the same time. When my hall thermostat calls for heat all of the UFH loops downstairs come on and all the rads ...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Mitsubishi Ecodan stuck on immersion symbol

Yep that all makes sense the easiest solution is to remove all the actuators from the UFH manifold they should just unscrew them all loops will be ope...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Mitsubishi Ecodan stuck on immersion symbol

So presumably the EPH thermostats are wired back to a controller near to the UFH manifold? Do you have a picture of that?

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Mitsubishi Ecodan stuck on immersion symbol

That will be the cause then, with only 1 thermostat calling for heat the water volume is too small it heats quickly and the heat pump has to turn off ...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Mitsubishi Ecodan stuck on immersion symbol

That’s definitely cycling do you have UFH or rads regardless of which it would suggest you have only a very small proportion of the heating system cal...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Mitsubishi Ecodan stuck on immersion symbol

They could be defrosts but unlikely at that Frequency. do you have the MELCloud app that can show the flow and retune temps for those times? There...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Analysing MELcloud heat pump graphs

It’s an 8.5kw ecodan UFH and rads. WC set at 32C at 3C, 45C at -10C. Running on weather comp with thermostat set to 22C in the hallway. Once it g...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Mitsubishi Ecodan stuck on immersion symbol

@ak2024 that is the HP cycling on and off 2/3 times an hour usually happens at milder outside temps when the flow temp is around 30C or less. I have ...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: Analysing MELcloud heat pump graphs

@boycey what you have there is really bad cycling 10 times an hour. if you increased the flow rate this will have only worsened it as it has less ti...

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Reply
RE: The Definitive Guide to Weather Compensation and Curves for Air Source Heat Pumps

@boycey in milder temps you have to limit heating with the thermostats so that’s set at 22C to turn the heat pump off till it cools back down again.

9 months ago
Forum
Air Source Heat Pumps (ASHPs)
Page 12 / 30
Share:

Join Us!

Podcast Picks

Latest Posts

Click to access the login or register cheese
x Powerful Protection for WordPress, from Shield Security
This Site Is Protected By
ShieldPRO →