Last seen: Dec 18, 2025
Hi @Soniks, that's really bad news. Has the ASHP installation been installed by a Grant G1 approved installer? If it has, and is has been serviced and...
My Grant has an auxiliary output contact, which is used to control a separate 3kW immersion heater via a relay. It's a back-up heater, supplementary h...
'Elephant in the room' photo that first one showing monobloc location, it was never going to run efficiently. Sadly all too common. Sometimes it's ins...
Hi Mars, generally the higher the voltage the more powerful the portable tool. But a higher voltage battery can provide a longer run time than a lower...
@ggw True electrical usage requires power monitoring & logging of the ASHP monobloc and any additional circulating pumps, controls, etc. There is ...
In a word 'yes'. Battery powered portable tools are designed to work only at their specified voltage. Most portable tools will accept only the correct...
@ggw we have the heating running about 17hrs a day, on early morning around 4.30am, off abound 9.30pm. 1.25 hours in the middle of the day set of HW. ...
We have a grant pre-plumb cylinder with digital thermostat. Thermostat reading is all over the place, still giving us hot water at 45degC when the the...
@iaack hi again. The flow sensor is external on the system hot water cylinder on Samsung Gen6, not internal to the monobloc, so it's possible to have ...
I thought I would share this DIY split system air to air a/c install. This is an R290 propane unit sold by Appliances Direct after the buyer said he w...
- 26 Forums
- 2,360 Topics
- 53.5 K Posts
- 242 Online
- 6,026 Members
Join Us!
Worth Watching
Latest Posts
-
RE: New Fogstar 15.5kWh upright solution
Easy to spot the second collaborator. 🤣 So w...
By Batpred , 3 minutes ago
-
RE: Say hello and introduce yourself
@velcro welcome to the forums. Please feel free start a...
By Mars , 14 minutes ago
-
RE: Speedcomfort radiator fans
I watched the video to see whether they'd potentially b...
By Sheriff Fatman , 33 minutes ago
-
I will report back with an update on ours in due course...
By Sheriff Fatman , 37 minutes ago
-
RE: Mitsubishi Ecodan R290 10kW performance
@ecoste For what it's worth, this is my equivalent data...
By Sheriff Fatman , 1 hour ago
-
Daikin EDLA11D3V3 DHW Settings
I have a newly installed EDLA11D3V3 which I'm still get...
By Velcro , 1 hour ago
-
RE: Setback savings - fact or fiction?
Will come back to the above points, but for now, I've j...
By cathodeRay , 2 hours ago
-
@jamespa I have found that it comes as a shock when we ...
By Toodles , 3 hours ago
-
RE: My Powerwall 3 Consumes 3-4 kWh/Day in Self-Consumption: Is This Normal?
I suspect a good chunk of the "losses" are power consum...
By Bash , 4 hours ago
-
RE: Need Help Optimising My Rushed ECO4 Install: 12kW Bosch Heat Pump
Hi @mickamills . Welcome to the forum. It sounds like...
By bontwoody , 5 hours ago
-
RE: Midea ASHP – how to set weather compensation
@curlykatie did you get sorted with this?
By MickaMills , 5 hours ago
-
RE: External pipework insulation
@transparent I hope you are not being admonished @trans...
By Toodles , 5 hours ago
-
RE: Octopus Cosy Heat Pump Owners & Discussion Thread
The FT levels off at either the set point OR the minimu...
By AndrewJ , 1 day ago
-
RE: MyVaillant Connect Regular Disconnect
Thanks. Yes, if the time is consistently 11pm every nig...
By buckwem , 1 day ago
-
RE: Who's your electricity provider and what's your tariff?
@transparent Thanks, this helps. Could it be that St...
By Batpred , 1 day ago
-
RE: Clivet ASHPs and weather compensation
Simon did share a lot of very helpful advice. On furthe...
By ambris , 1 day ago
-
-
RE: Advice on internal circulation pump noise
Extend the primary branch and make sure you have more t...
By ASHP-BOBBA , 2 days ago


