Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Sep 1, 2026
that's on mine which is a 2021/22 FTC6 btw
@sliderule no worries at all. One black segment is quietest/min power. Three black segments is normal/full power (see photo)👍
-- Attachment is not available -- @skd do you think setting quiet mode might help with this ? [/quote]Sorry Rich I missed your question earlier. ...
@sliderule yes Quiet Mode is definitely worth a try for comparison. According to Mitsubishi techs it works by simply limiting the max compressor spee...
Ah okay. Sorry it wasn't any help.
Just to mention, if your Ecodan has sufficient spare capacity you could try running in one of the two Quet Mode settings. In addition to being quie...
@rod thanks, yes that figures. My max ASHP temp is currently set to 50degC. I need to increase it too
With a 60degC legionella set point, my ASHP takes the DHW temperature up to 50degC and then goes to standby, and the immersion heater takes over for t...
When our Ecodan system was first commissioned we had a low flow rate, very similar to this. The engineer simply cleaned the in-line strainer, and sin...
@sarah Hi, the highlighted "-30" your compensation curve is fine. The two highlighted parameters on the graph are just indicating the curve at the ma...
It was only about 5 degC lift that time. The compressor is in Quiet Mode so max output is less than 11.2kW and it takes a bit longer. The rest of...
@minos Hi - just to back up Kev's points, I had similar questions about our Ecodan R32 ASHP when we first switched off the heating and were only runni...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Siting of the external sensor on a heatpump
@bobflux My Daikin ASHP is SSW facing and the wall behi...
By Toodles , 8 minutes ago
-
RE: Recommendations in Ely (Cambs) area for Full setup checks on Nibe HP setup for House.
I can't help with your principal question but as a matt...
By JamesPa , 3 hours ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
You should (almost) always reject having a buffer, by w...
By JamesPa , 22 hours ago
-
RE: Navigating the World of Refrigerants In Heat Pumps: A Guide for Homeowners
Indeed we are invvestigating AC at present and are havi...
By Toodles , 1 day ago
-
RE: Is it the house or the equipment?
@majordennisbloodnok I do sympathise. On the original...
By springswood , 1 day ago
-
No, but the heat pump must be capable of delivering a S...
By JamesPa , 1 day ago
-
Sorry to hear about the problems, its going to be somet...
By JamesPa , 1 day ago
-
RE: Daikin ESPAltherma and Home Assistant installation
It's laziness lol The PV system is very chatty, meter...
By bobflux , 2 days ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
R (The R Project for Statistical Computing, I use it wi...
By cathodeRay , 2 days ago
-
RE: Vaillant Arotherm Plus 7KW need a service on it
booked it with Vaillant. will use them until i can find...
By AdamK , 2 days ago
-
RE: Adventures in heat loss calculations
I have seen it stated that the declared calorific value...
By JamesPa , 2 days ago
-
RE: Two heating zones to one zone
@transparent Many thanks. The garage is fairly well ...
By Profzarkov , 3 days ago
-
RE: Vaillant Aurotherm - Heater Wire Position
Ah, good point. I need to check if this was installed i...
By Batpred , 3 days ago
-
@batpred thanks for getting a copy. Appreciate the supp...
By Mars , 4 days ago
SPONSORS
