Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Aug 21, 2024
A reply from Vishay: your inquiry: "Are you aware of a device or method of converting the resistance output from a Pt1000 sensor to the equivalent r...
I asked OHMIGO® what curve they used for their NTC 20 kΩ table and received a very swift and useful reply: There are small variations between suppli...
Good suggestion. I am in the process of doing something similar to see which of the 15 (1-14, 17) Vishay curves is a good fit (It will also be interes...
It works fine but the integration with the rest of the system is rather clumsy. For solar back off, a relay in the SKSC2 drives a contactor which adds...
Requirements are for reliability and acceptability to heating installers / maintainers. Ideally, a ready made device with safety approvals (may not ex...
My guess would be a Digital potentiometer. Might need a logarithmic one to cover the NTC 20 kΩ resistance range? I'm not an electrical engineer so thi...
The Pt1000 Resistance Table is straightforward. NTC Thermistors, Resistance/Temperature Conversion is more complex. I know it should measure 20 kΩ at ...
Probably should have mentioned that the solar collectors are on a second floor sloping roof. Front of the house is almost on the footpath. Access to s...
I would like to know if they offer design advice and can recommend installers that might consider upgrading my existing system. There is a good supply...
Oops! Wrong pump. I have been informed that we have Grundfoss UPM3 HYBRID 25-70 180 ACA pumps. Sorry for the confusion. According to UPM3 Installation...
SPONSORS
Degrees of Separation
Latest Posts
-
Vaillant Arotherm Plus 7KW need a service on it
looking for a service to be done on my heat pump, im ba...
By AdamK , 6 minutes ago
-
RE: Two heating zones to one zone
@transparent Many thanks. The garage is fairly well ...
By Profzarkov , 2 hours ago
-
RE: Vaillant Aurotherm - Heater Wire Position
Ah, good point. I need to check if this was installed i...
By Batpred , 7 hours ago
-
RE: Adventures in heat loss calculations
Posted by: @jamespa At this point its probably worth...
By Rob of York , 9 hours ago
-
@batpred thanks for getting a copy. Appreciate the supp...
By Mars , 19 hours ago
-
RE: Tell us about your Solar (PV) setup
We have a 6.56kW solar PV system (16x 410W panels) inst...
By Rob of York , 1 day ago
-
RE: Where heat loss surveys seem to go against practical reality
@cathoderay @jamespa I've managed to get some nice re...
By Rob of York , 2 days ago
-
RE: 7kW EV Charger Options Advice
Doh, not sure that I was thinking straight there, less ...
By Rusty , 2 days ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
I’m really liking reading through this thread and the r...
By Judith , 2 days ago
-
Thank you @trebor12345
By rgabor , 2 days ago
-
Panasonic Free Multi Z and Etherea Internal units.
My prospective installers have suggested the Panasonic ...
By Toodles , 3 days ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
Great. You just need to find a way of cranking up your...
By JamesPa , 3 days ago
-
RE: Heat Pumps Without Grants: Would You Have Installed One & Will You Now?
We had two heat pumps installed without Govt funding. H...
By Rob of York , 3 days ago
-
My Adapt is finally installed and running! Almost a yea...
By tomasmcguinness , 3 days ago
SPONSORS
