
Last seen: Jul 4, 2025
@grumpidoc You may be interested in what I have done to reduce my system noise. My system is Ecodan 11.2kw > Primary Pump (Grundfos UPS2 25-80) &...
@boycey Yes, the thermostat on my Ecodan is on the back in the top corner. When the engineer replaced the thermostat, I suggested that it could perh...
@boycey Legionairres taking too long: Mitsubishi diagnosed a defective immersion heater. Installer is coming next week to replace it. Outside temp...
@trbob I went down the Mitsi Engineer route unfortunately with the fee. Report has just come in to say that the immersion had "irregular figures whe...
@trbob Very interesting. It took round about an hour for your immersion to get from 49.5 to 59.5. Probably acceptable It looks like the Mitsi soft...
@toodles I guess you are trying to create a bit of shade. Not sure if the wife will agree to blocking the kitchen window and to be honest, unless it...
@toodles My gap is 39 although there is plenty of room in front of the ecodan if I wanted to move it forward a bit and maybe move the plant pot a bit ...
@transparent the details on the plate are: 000003402550 RT IH IN1 14/RTS-ERP A 3KW 240V
@toodles Thanks. The problem is that the Outside temperature gain only occurs when it's sunny. Normally it's ok. I think the heat on the wall behind...
@transparent Thank you for your comments. Unfortunately what you suggest I do is beyond my technical abilities so I will have to wait for the instal...
@trbob Sounds like the software is switching off the immersion at 59.5c and as it's not reaching the desired 60c, it continues with the cycle waiting ...
@transparent Thanks. You have confirmed my belief that when running the immersion it should reach the desired 50 > 60c after 1 hour confirming my g...
- 23 Forums
- 2,098 Topics
- 46.2 K Posts
- 282 Online
- 3,385 Members
Latest Posts
-
RE: Ecodan consuming 100kwh per day in new build!!!
@anca1808 I have just reviewed the whole thread. In s...
By JamesPa , 15 minutes ago
-
RE: Heating coming on when not required
I played with a max heating temp but there is a world o...
By JamesPa , 11 hours ago
-
RE: Pressure drop Primary circuit
I've always regarded topping up heating systems as my j...
By JamesPa , 11 hours ago
-
RE: Heat pump solutions and/or installer recommendations for France
I’d travel to France for work if you were struggling wi...
By Damon Blakemore , 18 hours ago
-
RE: 5 Star Service from Havenwise
That's always a danger with any new good idea, @morgan....
By Majordennisbloodnok , 23 hours ago
-
Have your say in the Renewable Heating Hub Awards
It’s time to celebrate the best (and call out the worst...
By Mars , 1 day ago
-
-
RE: Mitsubishi cycling while on chilled water output
@iaack yes there's no denying that cold air sinks! I s...
By downfield , 2 days ago
-
RE: Weather compensated secondary circuits with Biomass
@andycoo that flooring sounds ideal. Extra volume is ...
By Sune , 2 days ago
-
If you are thinking of heating on the immersion conside...
By JamesPa , 3 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@tomasmcguinness, I think your best bet would be using ...
By Aventus Eco , 3 days ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@toodles all depends on asking the right questions! And...
By Tim441 , 3 days ago
-
RE: Commencing on an ASHP Installation Process
I received confirmation this morning that my Greener Ho...
By Sheriff Fatman , 4 days ago
-
@jamespa Thanks for the advice - very helpful. I had al...
By abam48 , 5 days ago