Last seen: May 9, 2025
I found this post of mine recently and was to report back by @heacol on findings since the post. However, my system has been significantly improved s...
Gonna challenge a few things here... I'm not sure those correlate. The system can be set to use 'flow temp' mode (Mitsubishi speak for fixed fl...
Not my area of expertise so won't comment on that. I assume 'the ecodan board' is the 'FTC' (flow temperature controller) - you can see the FTC6...
If you're technically-minded you can probably figure it out, though it may take a while to sink in. If you've adjusted the dipswitches already, you'v...
@sliderule - see my related earlier post, atbr />
In another post, @jamespa wrote: Yes! Well, I guess slightly-more nuianced - see below. The lower flow temp constraint (in bold) is useful t...
(Answering in the referenced post)
I was in two minds whether to comment here or start a new post - I decided the latter as this was specifically about reference material for CoP vs flo...
No, I don't - reading@heacol recommends removing the mag filter and adding a Y strainer! Thoughts?? Agree, however would the DN19 of the flow se...
Also, in terms of positioning of the 22mm-based components, I'd be keen to know others thoughts on where these would go to optimise flow and their per...
@johnr The question at that point is, as posed in the OP, for those to go back through 22mm flow sensors and a mag filter to the return to the outdoor...
Latest Posts
-
Delighted to hear this went well. It looks very neat ...
By JamesPa , 7 hours ago
-
RE: No-code, plug-and-play monitoring for your heat pump
The issue with the Grant is that you have to wire direc...
By Grantmethestrength , 11 hours ago
-
RE: Is this just haze or something more?
I am not a scientist nor a meteorologist and I know the...
By Toodles , 11 hours ago
-
RE: Benefits of an extra horizontal loop for GSHP
It will improve performance, but by how much depends on...
By Brendon Uys , 16 hours ago
-
RE: The good, the bad and the not that great – my heat pump installation
Said I would pop back with a update. Only Mr Jesus h...
By Burtis , 1 day ago
-
RE: Buffers, hot water and cooling
Thats presumably heat pump DT, what about radiator DT a...
By JamesPa , 1 day ago
-
RE: Who's your electricity provider and what's your tariff?
@chandykris Exactly the same here. We now have 13.5kWh ...
By Old_Scientist , 2 days ago
-
Compressor and Evaporator Stratification
I have had a few issues with my Hitachi spilt heatpump ...
By trebor12345 , 2 days ago
-
RE: Wood burner with ASHP - direct air?
This depends on the size of your wood burner and size/t...
By Lucia , 2 days ago
-
RE: Difficult positioning of air source heat pump
@rikiarn It's a not a buffer it's a volumiser which is ...
By Lucia , 2 days ago
-
RE: Is your heat pump insured?
To make things clear, lots of insurance companies cover...
By Lucia , 2 days ago
-
RE: Boxt Heat Pump Installation Experience
@adrian any updates since installation? How is it perfo...
By Ashfp , 3 days ago
-
RE: Say hello and introduce yourself
Hi @seatonian - Yes, I know Seaton, and I have the Nat...
By Transparent , 4 days ago
-
@seatonian got your email. Will connect you with a reco...
By Mars , 4 days ago
-
@downfield and @toddles, this isn’t in the settings cur...
By Mars , 6 days ago
-
RE: Homely launched for Grant Aerona ASHP control
I haven't bought the Aerona Smart Controller (£700!) bu...
By Prunus , 6 days ago
-
RE: Antifreeze top up for my heat pump - is this a rip off?
For the record, Grant supply ethylene glycol for their ...
By Prunus , 6 days ago
-
RE: Compressor attempts start but fails - Nibe Fighter 2005 8kW
@skyefarmer amazing. Well done!
By Mars , 7 days ago
-
RE: Air source heat pump roll call – what heat pump brand and model do you have?
Ebac 5kw - Monobloc R32. Developed and made in UK - Mit...
By marcinwloch69@gmail.com , 1 week ago
-
RE: Is a Valliant Inline 6kW heater a BUS buster?
Just another thought - it might be worth thinking about...
By JamesPa , 1 week ago
