Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering youāll be able to ask questions, join discussions, follow topics youāre interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Feb 13, 2025
@toodles @richard24738 and @gary Just reporting back. It became clear that much of the noise was from the primary pump. We have finally had a visit f...
Thank you @richard24738 and @gary you have been so helpful! I will post back here when we finally get it sorted.
@richard24738 and @gary Thank you so much for your input - I am learning loads and I think my brain is going to explode! I think I'd better take a ste...
@toodles thanks - I'll search out that presentation
@gary We have a single zone, all radiators, though a fairly long run from one end of the bungalow to the other. the cylinder and pumps are pretty mu...
@harriup and @gary finally got a moment to think about the pump - turns out the Wilo has a display which shows pump speed (though in cubic metres / hr...
We've just done the exact same thing, we're with Octopus. They advised we needed to get our usual gas engineer to disconnect any gas appliances in the...
Thank you @harriup and @gary this is all very helpful. The paperwork just states a rust inhibitor and 'antifreeze' and it looks like we have an anti-f...
We do, tho I would need to check if the concentration is sufficient. If we did that in this freezing weather would that mean the cooling fins on the...
@toodles thank you for your input. We balanced it ourselves as best we could, but will have another go at it. However it is worst in a bedroom with th...
- 27 Forums
- 2,761 Topics
- 65 K Posts
- 1,181 Online
- 7,168 Members
Join Us!
Installer Finder
Degrees of Separation
Latest Posts
-
RE: Adventures in heat loss calculations
This thread being the more generic one is I think the b...
By cathodeRay , 1 hour ago
-
RE: Tell us about your Solar (PV) setup
Our PV set-up has moved over time. Warning this is a sh...
By Judith , 13 hours ago
-
RE: Where heat loss surveys seem to go against practical reality
@cathoderay @jamespa I've managed to get some nice re...
By Rob of York , 20 hours ago
-
RE: 7kW EV Charger Options Advice
Doh, not sure that I was thinking straight there, less ...
By Rusty , 22 hours ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
Iām really liking reading through this thread and the r...
By Judith , 24 hours ago
-
Thank you @trebor12345
By rgabor , 1 day ago
-
Panasonic Free Multi Z and Etherea Internal units.
My prospective installers have suggested the Panasonic ...
By Toodles , 2 days ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
Great. You just need to find a way of cranking up your...
By JamesPa , 2 days ago
-
RE: Heat Pumps Without Grants: Would You Have Installed One & Will You Now?
We had two heat pumps installed without Govt funding. H...
By Rob of York , 2 days ago
-
My Adapt is finally installed and running! Almost a yea...
By tomasmcguinness , 2 days ago
-
-
RE: Being screwed over by Volkswagen Audi Group
Thanks, @batpred. That integration is the one I have in...
By Majordennisbloodnok , 5 days ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@batpred I suspect it will be more this year. I had 9 ...
By AndrewJ , 5 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@jamespa It's rusting š
By tomasmcguinness , 5 days ago



