Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Jun 26, 2026
Hi @Mike, says 65degC on the Samsung Data sheet/p> Other data sources support this:
Hi @roel. Welcome 🙂 The Samsung Gen6 12kW ASHP can heat water up to 65degC, which would charge your DHW tank to 60degC within a reasonably short ti...
Hi again @mellow, had a play with my DHW timer to see if I can replicate your issue. Right, there are four zones and each can have up to 4 time period...
Hi @Mellow, I hope I can help, as I have the same Grant 10kW ASHP, Grant branded Heatmiser 4 channel DHW thermostat and a 210L Grant pre-plumbed cylin...
@jennyross a couple of thought on this one: Vaillant ASHP monobloc support: If the installer used an existing base, such as a patio, then subsequent...
InstallerSHOW 2024 opens today at the NEC in Birmingham. Here's a thread for discussions on new products, developments, news, etc. Grant launch thei...
I've ditched the weekly 1hr Legionella cycle using the 3kW immersion heater fitted to a Grant 250L pre-plumbed cylinder. I was finding it ineffective ...
Sadly a very significant downside, turned out the 'too good to be true' HFO synthetic refrigerants like R1234yf and R1234ze were, well, too good to be...
Yes, I have the 'Home-me' (TM) integration system too. Similar set-up, stuff like Growatt Solar + batteries + Grant [Chofu] ASHP. All should just be s...
@matenateson it's good. Welcome on board! We have a modest 3.6kW 9 panel array on a house which one company dismissed as 'not suitable for solar PV' b...
Hello @davesoa, some things I would cross check between different heat loss calculation estimates, in order of greatest influence on heat loss estimat...
Hi @editor, a lot of damp is mis-diagnosed as rising. Often it is penetrating damp through the fabric, common in older solid wall properties in the co...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Volumisers in Heat Pump Systems: Does Placement Matter?
Volumisers are normally plumbed so that they are in the...
By JamesPa , 2 hours ago
-
@toodles possibly. The £9k labour charge for 4-5 days w...
By AndrewJ , 6 hours ago
-
RE: Plug and play solar. Thoughts?
My thought is simple. Bring it on and bring on plug in...
By JamesPa , 10 hours ago
-
RE: Heat Geek mini store vs pump size
Yes I agree, that’s why Heat Geek have most likely sele...
By Tomtheheatingengineer , 24 hours ago
-
RE: Who's your electricity provider and what's your tariff?
@chandykris Swings and Roundabouts, you win some…. ...
By Toodles , 24 hours ago
-
@tomtheheatingengineer, thank you, and welcome to the f...
By Mars , 1 day ago
-
RE: HeatGeek vs Octopus surveys: puzzling disparity - any ideas why?
@majordennisbloodnok @tomtheheatingengineer For my ...
By JamesPa , 1 day ago
-
RE: Do I add Air Con or MVHR to existing A2W ASHP?
There is scope for product development here. I for one...
By JamesPa , 1 day ago
-
RE: Is the "divide by 2900" rule still valid?
Really flow rate is a pipework limitation not a water p...
By JamesPa , 2 days ago
-
RE: The good, the bad and the not that great – my heat pump installation
@burtis, I’ve followed this thread pretty much from the...
By Mars , 5 days ago
-
RE: Starting Our Heat Pump Journey: 1962 build 3 bed detached house
First time poster here but I can share my experience as...
By SCH , 5 days ago
-
RE: Is it the house or the equipment?
...which, I've found out, is pretty much impossible to ...
By Majordennisbloodnok , 5 days ago
SPONSORS
