Why run a disinfectant cycle ?
My heat pump has been dutifully running the disinfectant cycle every week, but I read and hear that the jury is still out on whether this is really necessary. What do other people think ?
I have to go into Installer mode to change it, and I can only run it at the same time every week, or not at all. As it uses a significant amount of energy I would have liked to be able to control the timing eg run it when the grid is producing lower co2 electricity, or when the outside temperature is warmest.
If it's not really necessary I'm going to switch it off and get a much better COP.
Posted by: @heat-pump-newbieMy heat pump has been dutifully running the disinfectant cycle every week, but I read and hear that the jury is still out on whether this is really necessary. What do other people think ?
I have to go into Installer mode to change it, and I can only run it at the same time every week, or not at all. As it uses a significant amount of energy I would have liked to be able to control the timing eg run it when the grid is producing lower co2 electricity, or when the outside temperature is warmest.
If it's not really necessary I'm going to switch it off and get a much better COP.
If your water is already at 50C then you're going to have to heat it 10 deg to 60. For a 200l tank that's circa 8kwh at a COP of 1. So a couple of quid a week at the most. You could always have a really hot legionella-free bath to make up for it.
On the other hand the risk is extremely low (1) of legionella getting into your unvented cylinder and (2) you catching it from said cylinder.
It also doesn't like even moderately hot water (this from Wikipedia):
Temperature affects the survival of Legionella as follows:[3]
- Above 70 °C (158 °F) – Legionella dies almost instantly
- At 60 °C (140 °F) – 90% die in 2 minutes (Decimal reduction time (D) = 2 minutes)
- At 50 °C (122 °F) – 90% die in 80–124 minutes, depending on strain (D = 80–124 minutes)
- 48 to 50 °C (118 to 122 °F) – can survive but do not multiply
- 32 to 42 °C (90 to 108 °F) – ideal growth range
- 25 to 45 °C (77 to 113 °F) – growth range
- Below 20 °C (68 °F) – can survive, even below freezing, but are dormant
I would have thought the risk with HW at 48 deg is vanishingly small and that you're in more danger from scalding yourself with your 60 degree, guaranteed legionella free water once a week.
I think it is probably unnecessary but we will never hear the end of it from boiler fans if a heatpumped tank hosts an infection, so I have the standard controller set to still run the cycle the least often as a safeguard (monthly I think, at 0100GMT so cheap electricity and before the coldest part of night) and my add-on smart controller heats a tank of 52˚c water on any moderately warm late afternoon (so cheaper heating) which should kill most of it.
For best risk reduction, remember to run any seldom-used hot taps every so often, especially if the pipe to it is in a warm place such as next to heating pipes. Still water in pipes is probably a far bigger risk than the tank.
-
Nibe F2040 periodic warm water increase fails
2 months ago
-
Heat Pump, DHW, UFH and Radiator Install
9 months ago
-
Sudden drop in COP
1 year ago
-
Mitsubishi Ecodan - Hot Water Settings
2 years ago
-
Legionella cycle: Heat Pump or Immersion Heater?
2 years ago
- 26 Forums
- 2,118 Topics
- 46.6 K Posts
- 46 Online
- 4,523 Members
Join Us!
Latest Posts
-
RE: Help me keep the faith with my air source heat pump installation
So in summary it was a decision between pragmatism and ...
By JamesPa , 41 minutes ago
-
RE: Double or Triple Glazed Windows?
As I have reported elsewhere, we replaced all our glass...
By downfield , 4 hours ago
-
How to waste energy (and time) playing with AI.
A friend of mine who subscribes to an AI service was ex...
By Toodles , 5 hours ago
-
FRV valves - can you mix and match
Great video again this week @editor, I am very interest...
By Grantmethestrength , 5 hours ago
-
-
RE: Heat Pump Books For Beginners – Bodge Buster & From Zero To Heat Pump Hero
@topher you’re more than welcome to, yes. I’ll send you...
By Mars , 1 day ago
-
RE: Fitting new shower valve ..........
I’ve never taken a chance when fiddling and changing ou...
By Mars , 1 day ago
-
You should contact the council and report the unsatisfa...
By JamesPa , 1 day ago
-
RE: Benefits of an extra horizontal loop for GSHP
I would deffo install an additional slinky run, especia...
By Transparent , 2 days ago
-
RE: Say hello and introduce yourself
@editor fab - thanks Mars, and keep up the great work o...
By normpang , 2 days ago
-
RE: Compressor and Evaporator Stratification
@trebor12345 So I think the 1st zigzag section shows so...
By ASHP-BOBBA , 2 days ago
-
RE: Is this just haze or something more?
@majordennisbloodnok I was giving a talk to primary sch...
By Toodles , 2 days ago
-
RE: Tesla Powerwall – More of a ‘Luxury’ Than an ROI Winner!
We had our Tesla Powerwall 3 (and Gateway) installed ea...
By Old_Scientist , 2 days ago
-
Indeed. With a battery its presumably the battery con...
By JamesPa , 3 days ago
-
RE: No-code, plug-and-play monitoring for your heat pump
To update an ESP device using ESPHome in Home Assistant...
By Grantmethestrength , 3 days ago
-
RE: The good, the bad and the not that great – my heat pump installation
Said I would pop back with a update. Only Mr Jesus h...
By Burtis , 6 days ago
-
RE: Buffers, hot water and cooling
Thats presumably heat pump DT, what about radiator DT a...
By JamesPa , 6 days ago
-
RE: Who's your electricity provider and what's your tariff?
@chandykris Exactly the same here. We now have 13.5kWh ...
By Old_Scientist , 7 days ago
-
RE: Wood burner with ASHP - direct air?
This depends on the size of your wood burner and size/t...
By Lucia , 1 week ago
-
RE: Difficult positioning of air source heat pump
@rikiarn It's a not a buffer it's a volumiser which is ...
By Lucia , 1 week ago