Last seen: Jul 17, 2025
Can I refer back to your first post in this topic? You stated your strategy was to use three battery packs.The only cables which have to carry a pos...
That will probably work fine, but is noisy and doesn't offer the optimal strategy. The output side of a fan has turbulent air.It's 'out of control' ...
I'm unsure of the sources from which you derived your initial list, but I'm pleased to see it being altered as others contribute to this topic. Low-...
I'll have to think a bit about the balancing method. I'm not familiar with the Active-Balancer you're using.The ones I have here are the larger/newe...
No, it's the existing Seplos BMS which will be getting warm.It should be burning off the extra voltage through its resistors.The whole point of a pass...
The active balancer is only measuring differential voltage. Since each wire has approximately the same resistance added to it by the fuseholder, the v...
Interesting points you're making @robl There is probably little harm in doing things unconventionally... especially when in discussion with others o...
That was also my interpretation.But it doesn't seem to me a feature likely to be used by those reading this Forum. Keeping a battery topped-up is us...
Welcome @jeepster So you seem to have started out at the Rolls Royce end of the market with Victron kit,to which you then add the tried & truste...
If you need more help @majordennisbloodnok then please ask. You can post a photo of wires leading from your Growatt connection ports if you'd like c...
To save you flitting all over the place, let me re-post here a basic introduction to Modbus over RS485 RS485 is a serial protocol which runs ove...
So let me clarify... The simplest strategy is to use Modbus commands over RS485.The manual indicates at least two such ports are available for you t...
Latest Posts
-
RE: No-code, plug-and-play monitoring for your heat pump
We've got a svenar heat pump controller en route and lo...
By benson , 6 hours ago
-
RE: Air source heat pump roll call – what heat pump brand and model do you have?
Ebac 5kw - Monobloc R32. Developed and made in UK - Mit...
By marcinwloch69@gmail.com , 9 hours ago
-
RE: Is a Valliant Inline 6kW heater a BUS buster?
Just another thought - it might be worth thinking about...
By JamesPa , 13 hours ago
-
RE: BUS Grant: removal of all other fossil fuel heat sources
@rikiarn - just have a think as to how much it will cos...
By Transparent , 1 day ago
-
Don't do much digging around.That's best left to the pr...
By Transparent , 1 day ago
-
Hi all, I was wondering if anyone had an idea of how th...
By Wh0am3ye , 1 day ago
-
RE: EBAC re-entering the ASHP market in 2023
@toodles confirm i have Ebac 5kw ASAP + homely and it w...
By marcinwloch69@gmail.com , 1 day ago
-
RE: Compute heat loss from energy used
@jamespa Ebac must be similar to Mitsubishi as they buy...
By marcinwloch69@gmail.com , 1 day ago
-
@pie_eater I have been thinking of adding cooling to my...
By TechnoGeek , 3 days ago
-
RE: Victorian Semi Retrofit / Extension ASHP and UFH Advice
Agree, but you may have a hard time convincing them, as...
By JamesPa , 5 days ago
-
RE: Seal the Deal: Don't Let Your Heat Pump Leak Energy
Hi - fyi - there's a dead image link in the 'Optimal In...
By seatonian , 5 days ago
-
RE: Ripped Off: How UK Homeowners Are Paying Gas Prices for Wind Energy
@chandykris Horses and beggars…. 😉 Toodles.
By Toodles , 5 days ago
-
RE: Cleaning up after gas meter removed
@agentgeorge Likewise in the loft space; we have 300mm ...
By Toodles , 5 days ago
-
RE: Ecodan consuming 100kwh per day in new build!!!
This particular example is one of the worst I have seen...
By JamesPa , 6 days ago
-
-
RE: Fan running in hot weather ...why?
I wonder if it has some kind of pressure transducer to ...
By ASHP-BOBBA , 6 days ago
-
RE: Cooling with Samsung Gen6 and Flow error
@iaack The system isnt running long enough for any cond...
By EcoBaker , 6 days ago
-
@heacol thanks for confirming we can only hope NAPIT ag...
By Bart , 6 days ago
