Last seen: Dec 22, 2025
Hi yes we have FTC 5 but no flow meter was supplied so no energy reads. As we don't have this information on melcloud I just wondered if it just dupli...
Hi we moved into a new build ecodan already installed. There was no flow meter or energy data pack supplied with the install, so we have never been ab...
Yes mine does, my warm end of the curve is set to 33@7⁰ on my ecodan I can bring the whole curve down by off setting -4, when I do this my system runs...
@editor Hi its taken me 3 winters to get the curve right for our house, trial and error. New build well insulated 11.2 kW ecodan FTC 5 Ou...
Thanks @toodles @jamespa will get hubby to check this.
Thanks, will do.
This is the valve I have closed is that correct, will I need to bleed rads again?
Hi thanks for that, I'm not sure if I'm correct but I seem to remember having to open a valve to add pressure to the system. Would this be the valve ...
I agree re size, our property is approx 2100 sq ex garages and we have a 11.2 kw ecodan the property is L shaped well insulated dormer bungalow with ...
@mattc they did the install for all the properties on a small development. This was commissioned by the developer. What was extremely frustrating w...
Hi, Matt C I can only inform you of our experience with Greener Living. We moved into brand new property with newly installed mitsubishi ecodan and we...
Latest Posts
-
RE: Advice for a novice on Mitsubishi Ecodan 6kW
In my case it was a very specific pattern of behaviour ...
By Sheriff Fatman , 2 minutes ago
-
RE: Vaillant aroTherm not heating with many faults
@ashp-bobba Yeah I'll give it a go, will check filter...
By Anon67 , 11 minutes ago
-
@majordennisbloodnok it has been a few weeks since addi...
By TechnoGeek , 11 minutes ago
-
RE: RDSAP10 effect on existing heat pump EPC rating?
@transparent Perhaps the names at the end of the docume...
By Toodles , 22 minutes ago
-
RE: Predicted Heat Loss & Needs from MCS calcs vs EPC vs actual
COP of 3 perhaps a little low and you say that you don'...
By benson , 54 minutes ago
-
RE: Heatpunk Floor plan issues
@jamiejones85 A2A they will design on dynamic heat loss...
By ASHP-BOBBA , 1 hour ago
-
RE: Considering MLCP (Multi-Layer Composite Pipe) for ASHP
I think the concern was about crud being forced from th...
By iotum , 1 hour ago
-
RE: Recommended home battery inverters + regulatory matters - help requested
The usual type of underground cable with a metal 'outer...
By Transparent , 1 hour ago
-
RE: Rate the quality of your heat pump design and installation
Welcome to the forum and I am sorry you are disappointe...
By JamesPa , 1 hour ago
-
RE: Fan unit Making terrible noise HELP!!
can you post a video looking inside, at and through the...
By ASHP-BOBBA , 2 hours ago
-
RE: Setback savings - fact or fiction?
Excellent graphics and description Rob…. But to my mind...
By SUNandAIR , 2 hours ago
-
RE: Heat pump not reaching flow temperature
@davec Ive had a look at the screenshots. Lots of th...
By JamesPa , 14 hours ago
-
RE: Power outages and storms: A surprisingly good DNO experience
Agreed, which is no more nor less than a customer shoul...
By Majordennisbloodnok , 19 hours ago
-
RE: Running from backup generaor in powercut?
@batpred In our case, 3 times each day when the Octopus...
By Toodles , 19 hours ago
-
RE: New Fogstar 15.5kWh upright solution
@batpred Here's the latest Fogstar ready built pack....
By Bash , 21 hours ago
-
RE: Solis inverters S6-EH1P: pros and cons and battery options
Solis confirmed that the S6 works with a single battery...
By Batpred , 22 hours ago
-
RE: Who has a V2G EV installation
I am wondering if in any V2X, would the car battery eve...
By Batpred , 22 hours ago
-
RE: New Mitsubishi Ecodan 11.2kW installation - L9 errors and maybe more
OK. I think your system, which seems well designed, is...
By JamesPa , 1 day ago
-
RE: Fan is clipping ice build up from the front of unit.
@majordennisbloodnok I’ll not go there thanks! Toodles.
By Toodles , 2 days ago
