Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering youāll be able to ask questions, join discussions, follow topics youāre interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Dec 10, 2025
In this case, it uses the NASA protocol rather than modbus, but the register addresses are the same as far as I know. This is what it looks like on my...
I spoke to Homely about doing that, but he said that I would need to be a qualified electrician to become an approved installer. I have since installe...
@ashp-bobba Thanks very much for your detailed reply. That is really helpful. In situations where the flow rate can deliver heat at a DT of 5 C or les...
I suppose that might be true at a stretch if you were doing space heating throughout the summer, but who does that? I would dig your heels in until yo...
@ashp-bobba Welcome to the forum. I would be interested to understand the reasoning behind your statements. What was your experimental set up? I would...
Can you explain the mechanism for this effect? Could it just be coincidental rather than causal? System volume may prevent short cycling, but there ar...
With your 2091/2092 settings, the heat pump will only cycle off if your 3rd party thermostat is no longer calling for heat. If your home is warm, t...
Those settings exclude frequent cycling as the cause of poor efficiency. With 2091/2092 set to 'Use(Signal only ON/OFF)', FSV 2093 is inactive, so it ...
@raiph I apologise for my incorrect assumption. A PWM pump should maintain your delta T, so I am not clear why you are experiencing problems with a lo...
@raiph You seem to want a Delta T of 5, but your water pump has a fixed speed / flow rate which is currently 15 l/min. Your heat output is determined ...
@dinhp I will try and upload an audio file as it is difficult to describe how it sounds. The noise level will vary depending on how hard the heat pump...
@dinhp Thanks for the extra info. Your COP of 2.49 for today is not great if OAT is 9C, although it was probably colder overnight. Does this include a...
SPONSORS
Degrees of Separation
Latest Posts
-
RE: Tell us about your Solar (PV) setup
Our PV set-up has moved over time. Warning this is a sh...
By Judith , 2 hours ago
-
RE: Adventures in heat loss calculations
Agree with the first paragraph (I said roughly the same...
By JamesPa , 4 hours ago
-
RE: Where heat loss surveys seem to go against practical reality
@cathoderay @jamespa I've managed to get some nice re...
By Rob of York , 10 hours ago
-
RE: 7kW EV Charger Options Advice
Doh, not sure that I was thinking straight there, less ...
By Rusty , 12 hours ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
Iām really liking reading through this thread and the r...
By Judith , 13 hours ago
-
Thank you @trebor12345
By rgabor , 15 hours ago
-
Panasonic Free Multi Z and Etherea Internal units.
My prospective installers have suggested the Panasonic ...
By Toodles , 1 day ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
Great. You just need to find a way of cranking up your...
By JamesPa , 1 day ago
-
RE: Heat Pumps Without Grants: Would You Have Installed One & Will You Now?
We had two heat pumps installed without Govt funding. H...
By Rob of York , 1 day ago
-
My Adapt is finally installed and running! Almost a yea...
By tomasmcguinness , 2 days ago
-
-
RE: Being screwed over by Volkswagen Audi Group
Thanks, @batpred. That integration is the one I have in...
By Majordennisbloodnok , 4 days ago
-
RE: How Accurate Is My DIY Heat Loss Calculation?
@batpred I suspect it will be more this year. I had 9 ...
By AndrewJ , 4 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@jamespa It's rusting š
By tomasmcguinness , 4 days ago
-
RE: Glass lined Cylinder for private water supply
Thank you, once again, for your replies. Yes...
By ian33a , 4 days ago
SPONSORS
