Notifications

Clear all

How To Balance Radiators & the Role of the Lockshield Valve: A Homeowner's Guide

Toodles · 2024-04-11T06:06:00Z

Achieving the highest efficiency from your heat pump requires attention to your radiators. When set correctly, the pump will run more smoothly, with less noise and reduced 'short cycling,' leading to greater comfort due to more even temperature control in your rooms. I would also recommend setting your air source heat pump to 'Weather Compensation' and adjusting your 'Leaving Water Temperature' (LWT) to a moderate setting, starting with 35 degrees Celsius for the central area of the 'slope.' More guidance on setting 'LWT' can be found elsewhere; this article focuses exclusively on the 'Lockshield Valve' setting. The lockshield valve acts as a 'flow regulator,' controlling the amount of heat supplied from the flow pipe into the radiator. It should not be confused with the Thermostatic Radiator Valve (TRV) fitted at the other end of the radiator. The TRV serves as a temperature limiter, reducing the flow of heat only in extreme circumstances, such as solar gain heating up a room. Otherwise, the TRV should not restrict the flow. To begin setting up the valves, ensure all valves (both lockshield and TRVs) are fully open. Ideally, this task should be performed in colder weather to simplify the procedure. At this point, the heat pump can be turned on. Then, feel each radiator to determine which is warming up the most—make a note if necessary. The radiators, especially if newly installed, should have been sized according to room size and calculated heat losses, along with the desired room temperature. Starting with the radiator that warmed up the most, gradually close the lockshield valves from room to room. Initially, you might close the valve by two full turns, with final adjustments usually being half a turn or less from the fully closed position. Continue adjusting each lockshield on the next warmest radiator. Allow time for the radiator temperatures to settle after each round of adjustment. If some radiators remain warmer than others, they should be the first to be closed further. This process, requiring multiple steps of adjustment, aims to restrict flow minimally until each radiator sufficiently heats the room, allowing the rest of the heat to flow to other radiators. For instance, we prefer a warm bathroom and keep the lockshield valve fully open on this radiator, which is the first fed from the secondary pump circuit, keeping the room very cosy. Once the radiators provide proportionate amounts of heat for the rooms, allow the system to settle for about a day. Then, you might find some lockshield valves need a bit more tweaking. Proper adjustment takes time; although installers may make initial adjustments, fine-tuning to your comfort level is crucial. Consider using thermometers in rooms and a temperature probe on radiators to gauge progress. An infrared handheld thermometer can also assist in assessing radiator temperatures and the efficacy of your adjustments. If using a room thermostat, ensure it's correctly set so the radiator in that area warms the room to, but not above, the set temperature. Setting the thermostat slightly higher than desired can initially help avoid frustration. Once radiators are balanced, return to the heat pump controls for any final adjustments. TRVs should now be set to start shutting at approximately two degrees above the required room temperature. Under normal circumstances, TRVs will not disrupt the heating system but will activate if the room experiences solar gain or another heat source. An efficient heat pump system prefers a constant load and resistance to water flow; while a lockshield valve provides consistency, a frequently adjusting TRV can reduce the system's efficiency and increase operational costs. *Note: Installers might set a low temperature heat pump to a leaving water temperature of 45 or even 50 degrees Celsius by default, even though a lower temperature is more efficient and still provides adequate heat. Please note: While I am not an expert, plumber, or heat pump installer, I had an ASHP installed in 2023 and have carefully adjusted it after the initial commissioning. This required waiting for colder weather in December 2023 to fine-tune the lockshield valves and pump speed, achieving a COP well above 4 most of the time. At installation, the smart controller was not available, so a basic thermostat was installed. Setting this thermostat a few degrees above the required temperature prevented frequent on/off cycling. After installing the smart controller, the temperature is maintained within 0.6 degrees of the desired level. I also repurposed a programmable TRV from a previous gas boiler system for the bedroom radiator, allowing for temperature adjustments at night, while the other nine radiators remain with TRVs fully open.

Page 15 / 15 Prev

Thermostats, Volumisers, Buffer Tanks, TRVs, Pumps, Piping, Valves, Radiators & Controls

Last Post by JamesPa 2 months ago

172 Posts

9 Users

15 Reactions

7,342 Views

RSS

Alfapat

(@alfapat)

Reputable Member Member

Joined: 3 years ago

Posts: 182

07/05/2025 4:08 pm

At long last , I found a decent plumber and boiler expert locally to take the buffer out of the system(his advice) and change the piping the short distance that I had from the buffer from 22 to 28mm . Also down to one pump on the flow side directly into the CH and returning to HP . DHW remains as it was . A week into the modified system running and seems to be fine , there has been some frosty nights and cold airstream throughout the last two weeks, and that’s reflected with the heating on in the evening . I have brought the water law back to 38c from 40 , OK so far . Is Homely beneficial at this time of year?

👍

ReplyQuote

JamesPa

(@jamespa)

Illustrious Member Moderator

Joined: 2 years ago

Posts: 2623

07/05/2025 4:43 pm

Really delighted to hear that. I can't comment on homely but if you don't have it then you will likely want to readjust your weather compensation curve having removed the buffer. At this time of year it's probably nigh on impossible to get it right, most likely you will need to wait until the new heating season to get to final values. If you need any help please just ask!

This post was modified 2 months ago by JamesPa

4kW peak of solar PV since 2011; EV and a 1930s house which has been partially renovated to improve its efficiency. 7kW Vaillant heat pump.

ReplyQuote

Alfapat

(@alfapat)

Reputable Member Member

Joined: 3 years ago

Posts: 182

07/05/2025 7:07 pm

@jamespa So settings to date are as follows for now.

- **2011:** -10°C
- **2012:** 15°C
- **2021:** 40°C
- **2022:** 25°C

I have put 2022 to 38c

Will see how it goes thanks £2900 later !

ReplyQuote

JamesPa

(@jamespa)

Illustrious Member Moderator

Joined: 2 years ago

Posts: 2623

08/05/2025 2:41 pm

Good luck, I hope it all works out!

4kW peak of solar PV since 2011; EV and a 1930s house which has been partially renovated to improve its efficiency. 7kW Vaillant heat pump.

ReplyQuote

Page 15 / 15 Prev

26 Forums
2,104 Topics
46.3 K Posts
116 Online
3,393 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed

RE: Who's your electricity provider and what's your tariff?

@old_scientist Another point I might have made a little...

By Toodles , 1 hour ago
RE: Ecodan consuming 100kwh per day in new build!!!

It does indeed look like that, @skyefarmer. There is ...

By Majordennisbloodnok , 5 hours ago
RE: Plug and play solar. Thoughts?

Have a read of my previous posts on so-called Balcony S...

By Lucia , 23 hours ago
RE: Failed install (initial SCOP1.8), clueless installer compounded by poor manufacturer support. Help needed desperately!

@editor @bart Hi, I can see a few problems with your in...

By Brendon Uys , 1 day ago
RE: Compressor attempts start but fails - Nibe Fighter 2005 8kW

"To tell you the truth, I don't know if HAL is homicida...

By Scalextrix , 1 day ago
RE: Location of hot water isolation valve on cylinder

@rossowheels if you isolate the water supply in it will...

By ASHP-BOBBA , 2 days ago
The Importance of Radiator Balancing for Efficient Heating: Introducing the Flow Regulating Valve

It’s fascinating to watch how low-temperature heating i...

By Mars , 2 days ago
RE: Servicing Hitachi HP in rural Somerset

I'd give GreenGenUK a call or email them: sales@greenge...

By Mars , 2 days ago
RE: Heating coming on when not required

I played with a max heating temp but there is a world o...

By JamesPa , 3 days ago
RE: Pressure drop Primary circuit

I've always regarded topping up heating systems as my j...

By JamesPa , 3 days ago
RE: Heat pump solutions and/or installer recommendations for France

I’d travel to France for work if you were struggling wi...

By Damon Blakemore , 3 days ago
RE: 5 Star Service from Havenwise

That's always a danger with any new good idea, @morgan....

By Majordennisbloodnok , 3 days ago
Have your say in the Renewable Heating Hub Awards

It’s time to celebrate the best (and call out the worst...

By Mars , 4 days ago
RE: ASHP service costs

@ashp-bobba And super happy fish too I expect 😊...

By Toodles , 4 days ago
RE: Mitsubishi cycling while on chilled water output

@iaack yes there's no denying that cold air sinks! I s...

By downfield , 4 days ago
RE: Weather compensated secondary circuits with Biomass

@andycoo that flooring sounds ideal. Extra volume is ...

By Sune , 4 days ago

Forums

How To Balance Radiators & the Role of the Lockshield Valve: A Homeowner's Guide

Join Us!

RHH Awards

Latest Posts

Members Online