Last seen: Mar 8, 2023
I would be very interested in hearing more about your conversations with the trade about ASHP installations. We have had the original installers back ...
I had the unit set to 18 overnight (till 4am) and 19 from then on but this morning at 6am the temperature in the house was down to 17.5C It had not ri...
I failed to say that the design allows for a 50C flow temperature but since the engineer did some fettling I have not investigated it again.
@gfkw1947 I don't think that there has been a decrease in efficiency. I know I should be able to find the data on the efficiency but I do not know how...
@sapper117 I have set it to increase the temperature from 17C to 20C at 4am. It reduces again at 8pm.
Forum Handle: timatheronwood Manufacturer: Daikin Model: 3HT HT_767 High Temperature split (R32) Type: ASHP Arrangement: Split, High Temp, Biv...
@kev-m The Daikin engineer came out and installed two back up heater units under warranty as they had not worked from the start. Our problem with t...
SO the Daikin people called back and asked me to reset the thermostat from 20 to 23 to increase the requested load on the system. Success! The system ...
We had a Daikin Altherma 3 High Temp Split HHT (R32) installed in November 2021. It has never functioned well. We have had three Daikin engineer visit...
Hello everyone! We have a Daikin ASHP - Altherma 3 High Temp Split HHT (R32). We have had a number of issues with the unit unable to keep heating th...
- 26 Forums
- 2,406 Topics
- 54.6 K Posts
- 370 Online
- 6,092 Members
Join Us!
Worth Watching
Latest Posts
-
Experience - New Build / Complete New Heating System
Introduction We are in the process of completing a ne...
By vincro , 8 minutes ago
-
RE: Setback savings - fact or fiction?
Given the weather has been relatively stable, the empir...
By Batpred , 9 minutes ago
-
New Daikin 11kW Altherma 3M install - is it working as it should?
I had the system installed by Octopus in October last y...
By Synthbuilder , 20 minutes ago
-
RE: Rate the quality of your heat pump design and installation
🤣 what exactly did he dismiss and why?
By Mars , 39 minutes ago
-
RE: Post-Traumatic Heat Pump Stress Disorder
@jamespa Hi James - thanks so much! That sounds like ut...
By johnbroome , 54 minutes ago
-
RE: Heat pump not reaching flow temperature
@jamespa system design was for 40 degrees FT at -2 degr...
By DaveC , 1 hour ago
-
RE: GSHP WOES! Midland based engineer recommendations?
@editor That is very kind! Thank you so much.
By johnbroome , 1 hour ago
-
RE: Considering MLCP (Multi-Layer Composite Pipe) for ASHP
@iotum, this is a really good question and you’re right...
By Mars , 1 hour ago
-
RE: Recommended home battery inverters + regulatory matters - help requested
That matches the TN-C-S diagram here Your post crosse...
By JamesPa , 1 hour ago
-
RE: ASHP Energy Consumption: Aira 12kW heat pump
@wally Hi I am not sure how large your house is b...
By TechnoGeek , 2 hours ago
-
Please help with the settings ecodan
I have a 160 square meter house, first floor 6 radiator...
By nose1972 , 3 hours ago
-
RE: Predicted Heat Loss & Needs from MCS calcs vs EPC vs actual
I've been thinking along similar lines to @tim441 from ...
By Sheriff Fatman , 3 hours ago
-
Thanks, @technogeek. Good to hear about the accuracy. ...
By Majordennisbloodnok , 3 hours ago
-
RE: Advice for a novice on Mitsubishi Ecodan 6kW
In my case it was a very specific pattern of behaviour ...
By Sheriff Fatman , 4 hours ago
-
RE: Vaillant aroTherm not heating with many faults
@ashp-bobba Yeah I'll give it a go, will check filter...
By Anon67 , 4 hours ago
-
RE: RDSAP10 effect on existing heat pump EPC rating?
@transparent Perhaps the names at the end of the docume...
By Toodles , 4 hours ago
-
RE: Heatpunk Floor plan issues
@jamiejones85 A2A they will design on dynamic heat loss...
By ASHP-BOBBA , 5 hours ago
-
RE: Fan unit Making terrible noise HELP!!
can you post a video looking inside, at and through the...
By ASHP-BOBBA , 5 hours ago
-
RE: Power outages and storms: A surprisingly good DNO experience
Agreed, which is no more nor less than a customer shoul...
By Majordennisbloodnok , 22 hours ago

