Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: May 4, 2025
@andehh, do you have a way of monitoring the power being produced by the ASHP when the UFH is on or, failing that, can you check the Instantaneous Usa...
@jamespa thank you for your helpful comments. It has been very useful for me to write all this down and for someone else to sanity check it in case I ...
@jamespa - thank you for your comments. The plot of the compressor frequency is very interesting. Before I had the instrumentation sorted out I was ...
It is a 4 port buffer. Yes, there is a secondary pump on the UFH return to the buffer. The initial install included yet another pump on the sec...
@ecobaker Yes, it must have been a software bug disrupting my historic energy numbers. I haven't looked at them recently so I should check to see if t...
@ecobaker, How do the energy use and generation output differ between the good COP and bad COP weeks? Is it that the energy used has increased o...
@derek-m This has always confused me. The only way to change the FSV parameters I have found on my Gen 6 Wired Remote Controller is the Installat...
@lokisam, with the 20C outside air temperature I would think that the ASHP would not be working too hard so it is concerning that your readings are st...
@editor yes, the more I read the forum posts the more I realise that the Samsung issues tend to be the more challenging sort. The various manufactur...
@elton that's a cunningly devised methodology 😀 . As a self selecting group the visit a heat pump list will probably give a very accurate refl...
Thanks @lokisam We've been lucky over the last week with day temperatures in the 20s and night temperature only down to 11C so haven't had the heat...
- 27 Forums
- 2,763 Topics
- 65.1 K Posts
- 1,746 Online
- 7,169 Members
Join Us!
Installer Finder
Degrees of Separation
Latest Posts
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
@judith Thanks very much for this! My room by room calc...
By jon , 1 hour ago
-
RE: Vaillant Arotherm Plus 7KW need a service on it
I think that is outrageous even if I suspect not unique...
By Batpred , 2 hours ago
-
RE: Two heating zones to one zone
@transparent Many thanks. The garage is fairly well ...
By Profzarkov , 5 hours ago
-
RE: Vaillant Aurotherm - Heater Wire Position
Ah, good point. I need to check if this was installed i...
By Batpred , 11 hours ago
-
RE: Adventures in heat loss calculations
Posted by: @jamespa At this point its probably worth...
By Rob of York , 13 hours ago
-
@batpred thanks for getting a copy. Appreciate the supp...
By Mars , 22 hours ago
-
RE: Tell us about your Solar (PV) setup
We have a 6.56kW solar PV system (16x 410W panels) inst...
By Rob of York , 1 day ago
-
RE: Where heat loss surveys seem to go against practical reality
@cathoderay @jamespa I've managed to get some nice re...
By Rob of York , 2 days ago
-
RE: 7kW EV Charger Options Advice
Doh, not sure that I was thinking straight there, less ...
By Rusty , 2 days ago
-
Thank you @trebor12345
By rgabor , 2 days ago
-
Panasonic Free Multi Z and Etherea Internal units.
My prospective installers have suggested the Panasonic ...
By Toodles , 3 days ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
Great. You just need to find a way of cranking up your...
By JamesPa , 3 days ago
-
RE: Heat Pumps Without Grants: Would You Have Installed One & Will You Now?
We had two heat pumps installed without Govt funding. H...
By Rob of York , 3 days ago
-
My Adapt is finally installed and running! Almost a yea...
By tomasmcguinness , 3 days ago


