Last seen: Jan 5, 2023
@alec-morrow my kitchen has heavy, thick ceramic tiling but the VCR only shows one zone, so i guess I shouldn't lower the current curve setting from 0...
@transparent tbh, I'm not sure, I'll have to speak to the installer. Thanks for highlighting this key point I didn't know that Octopus offer that ta...
@alec-morrow thanks Alec. My heat curve is set at 0.8 and the heatmiser units set to 20. How low should i set the heat curve and how high should I s...
@transparent thanks for your reply. I'm rapidly getting my head around the complexities, it's a steep learning curve for sure and i'll be keenly wat...
Hi All, I found this via Mars YouTube channel and website - so thank you Mars! It's particularly interesting for me because I recently moved in to...
Latest Posts
-
We are 2 weeks away from our HP install. In October I...
By Bash , 3 minutes ago
-
RE: Experience - New Build / Complete New Heating System
Welcome to the forums @vincro and good luck with finali...
By Mars , 3 minutes ago
-
I’m glad the cold spell is over!
Just a sigh of relief that the cold spell is over and t...
By Judith , 14 minutes ago
-
RE: Heat pump not reaching flow temperature
@jamespa the compressor does run at max operating frequ...
By DaveC , 16 minutes ago
-
RE: Post-Traumatic Heat Pump Stress Disorder
@johnbroome As I say I think you probably have a fau...
By JamesPa , 27 minutes ago
-
RE: Recommended home battery inverters + regulatory matters - help requested
So far as i can see no because its NOT connected to the...
By JamesPa , 2 hours ago
-
RE: Please help with the settings ecodan
Hi and welcome to the forums.Does your system use a Mit...
By Sheriff Fatman , 2 hours ago
-
RE: New Daikin 11kW Altherma 3M install - is it working as it should?
I forgot to mention: Octopus measured our heat loss at ...
By Toodles , 3 hours ago
-
RE: Considering MLCP (Multi-Layer Composite Pipe) for ASHP
Thanks Mars and thank you for reaching out to so many p...
By iotum , 3 hours ago
-
RE: Air source heat pump roll call – what heat pump brand and model do you have?
Forum Handle: @davec Manufacturer: Peak Energy Mode...
By DaveC , 3 hours ago
-
RE: Rate the quality of your heat pump design and installation
@radwhispererdwhisperereorourkeditor Well, the guy came...
By razz , 3 hours ago
-
RE: Setback savings - fact or fiction?
Given the weather has been relatively stable, the empir...
By Batpred , 4 hours ago
-
RE: GSHP WOES! Midland based engineer recommendations?
@editor That is very kind! Thank you so much.
By johnbroome , 5 hours ago
-
RE: ASHP Energy Consumption: Aira 12kW heat pump
@wally Hi I am not sure how large your house is b...
By TechnoGeek , 6 hours ago
-
RE: Predicted Heat Loss & Needs from MCS calcs vs EPC vs actual
I've been thinking along similar lines to @tim441 from ...
By Sheriff Fatman , 7 hours ago
-
Thanks, @technogeek. Good to hear about the accuracy. ...
By Majordennisbloodnok , 7 hours ago
-
RE: Advice for a novice on Mitsubishi Ecodan 6kW
In my case it was a very specific pattern of behaviour ...
By Sheriff Fatman , 7 hours ago
-
RE: Vaillant aroTherm not heating with many faults
@ashp-bobba Yeah I'll give it a go, will check filter...
By Anon67 , 8 hours ago
-
RE: RDSAP10 effect on existing heat pump EPC rating?
@transparent Perhaps the names at the end of the docume...
By Toodles , 8 hours ago
