Last seen: Oct 1, 2025
@gunboatdiplomat The £2-3000.00 extra cost could very easily be eaten up in a few months, Last year I repaired a system with an average winter spend o...
I am not sure you realise the implication of design compromise. It can quite easily double your current heating bill, I have seen it many times. Would...
@lucia All BG installations are now installed using my open zome, high performing designs. All installations, weather installed by subcontractors, or ...
Caution everyone, this manual stipulates the installation of a buffer tank, so, the promised guaranty of supplying sufficient heat, may come at a very...
@ecobaker probably not
Yes, just make sure you have the correct flow rate at all times.
@bontwoody Maybe they have corrected it, I hope so.
@toodles Spot on, mostly from installers therefore end users, someone has to pay for it. However, that is only a very small part of the cost. I ran ...
@bontwoody That flow temperature is pretty close to 45 Deg C (43 deg C), it could be sensor drift that is causing the activation, it is clear that it ...
MCS and Heat Geek are not the same thing. MCS is a standard that any Heat Geek, or any other installer, has to abide by. It is not an installation sta...
@ecobaker They work reasonably well on open zone, just make sure you always have the minimum flow rate. Attached is a manual with the open zone prog...
@toodles The Heat Geek brand is just that, a commercial, moneymaking brand.
Latest Posts
-
RE: Replacing my 18 month old Hitachi Yutaki ASHP
I could do the change, I do have an electronics backgro...
By trebor12345 , 1 minute ago
-
RE: Solar panels on side of house to heat water
Yes, I have one in my Thermal Store. In the days befo...
By Transparent , 52 minutes ago
-
RE: Havenwise App Help & Forum Support – Get the Most from Your Heat Pump
@simonwig Thanks for the bump. Not sure why I didn't se...
By HCas , 2 hours ago
-
RE: Are Water Companies Delivering Bricks?!
...which in turn reminds me of a Thelwell cartoon I onc...
By Majordennisbloodnok , 2 hours ago
-
RE: Our journey through Octopus tariffs 2020-2025
I mentioned above "2025 move to Intelligent Go meant ...
By Tim441 , 2 hours ago
-
RE: Testing new controls/monitoring for Midea Clone ASHP
@benson — thank you, that is useful information you hav...
By cathodeRay , 5 hours ago
-
RE: Grant Aerona circulation/system pump staying on
My parameters are: 42 00 = 0 (so the next three value...
By MikeFl , 5 hours ago
-
RE: Electricity price predictions
My apologies. I should've written "The number and dep...
By Transparent , 5 hours ago
-
RE: Flow rate discrepancy between ASHP and manifold
@ashrolls Air circulating in the system will confuse fl...
By bornagain , 6 hours ago
-
RE: Help…my NIBE heat pump has faulted again!
If it happens only when it gets cold then it maybe that...
By JamesPa , 6 hours ago
-
RE: Grant Aerona3 - Home Assistant control via Modbus
Has anyone got past this screen to set up the integrati...
By AlanW1212 , 6 hours ago
-
RE: Heat Pump Training vs. Real-World Installation
@lucia have you discoveredfor how green each of our ene...
By Judith , 7 hours ago
-
RE: Diagnostic Data Needed for Repeatedly Failing Tesla Powerwall 3 System
You seem to be on the right track... Installers are rec...
By Batpred , 15 hours ago
-
RE: Should Our Water Circulation Pump Be Configured to Run All The Time?
there's a detect cycle setting (4200) on the old grant ...
By damonc , 17 hours ago
-
RE: Commencing on an ASHP Installation Process
@sheriff-fatman It's also worth highlighting that th...
By Lucia , 18 hours ago
-
RE: Hitachi Yutaki SCombi Heat Pump - Owners
. It does but, unless there has been a firmware updat...
By JamesPa , 21 hours ago
-
RE: Help me keep the faith with my air source heat pump installation
Yesterday it was chilly and the cosy6 had a Cop of 4.3 ...
By AgentGeorge , 23 hours ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@toodles Same here! This month 187kw.
By Andris , 23 hours ago
-
@jamespa Ah, they do indeed do firmware updates very oc...
By Toodles , 1 day ago
