Joining the Renewable Heating Hub forums is completely free and only takes a minute. By registering you’ll be able to ask questions, join discussions, follow topics you’re interested in, bookmark useful threads and receive notifications when someone replies. Non-registered members also do not have access to our AI features. When choosing your username, please note that it cannot be changed later, so we recommend avoiding brand or product names. Before registering, please take a moment to read the Forum Rules & Terms of Use so we can keep the community helpful, respectful and informative for everyone. Thanks for joining!
Last seen: Aug 17, 2023
Hi @Snuffy, we had the same with our Mitsubishi system, it did calm down after a while (a good few weeks). I found that there was air in the system se...
It's good that this thread is still going and from a selfish perspective I'm glad that it's not just me! Also, thanks @steevjo for posting the respons...
@squeakysim - that seems like a good quote. We installed an 8.5kw Ecodan and a Mixergy tank (more expensive than the normal system tank) at a cost of ...
Thanks @HarriUp. I'll look into those, I have also been looking at the Open Energy Monitor. Cheers Gavin
@Derek-M - good point, but I get COP envy.... More seriously though, I suppose, having a forum like this and enabling 'peer to peer' learning with t...
Hi @Cathoderay, thanks for starting this. I have almost exactly the same experience as you with multiple tabs open and nowhere to go! I am currently u...
Thanks for the additional info - yes, some small tinkling noises, and yes, only started using properly at the start of Nov. We do have air release val...
Hi, Here's my info Forum Handle: gfletcher Manufacturer: Mitsubishi Model: Ecodan 8.5kW with mixergy cylinder Type: ASHP Arrangement: Monobl...
Hi Derek, Thanks for the reply. Yes, I am topping up after bleeding. The pressure doesn't drop until I bleed the rads - but since installation I hav...
@morgan Brilliant - thanks, I'll look at the curve settings.
SPONSORS
Degrees of Separation
Latest Posts
-
No, but the heat pump must be capable of delivering a S...
By JamesPa , 8 minutes ago
-
RE: Next steps on my ASHP journey: Radiators and Pipework
TBH I dont understand how that works. Ultimately all th...
By JamesPa , 50 minutes ago
-
Sorry to hear about the problems, its going to be somet...
By JamesPa , 1 hour ago
-
RE: Daikin ESPAltherma and Home Assistant installation
It's laziness lol The PV system is very chatty, meter...
By bobflux , 14 hours ago
-
RE: Problems with sizing a replacement for a Viessmann Vitocal 200-S
R (The R Project for Statistical Computing, I use it wi...
By cathodeRay , 16 hours ago
-
RE: Vaillant Arotherm Plus 7KW need a service on it
booked it with Vaillant. will use them until i can find...
By AdamK , 17 hours ago
-
RE: Adventures in heat loss calculations
I have seen it stated that the declared calorific value...
By JamesPa , 22 hours ago
-
RE: Siting of the external sensor on a heatpump
Here's my heat pump running with a steady mildish 'OAT'...
By cathodeRay , 22 hours ago
-
RE: Two heating zones to one zone
@transparent Many thanks. The garage is fairly well ...
By Profzarkov , 2 days ago
-
RE: Vaillant Aurotherm - Heater Wire Position
Ah, good point. I need to check if this was installed i...
By Batpred , 2 days ago
-
@batpred thanks for getting a copy. Appreciate the supp...
By Mars , 2 days ago
-
RE: Tell us about your Solar (PV) setup
We have a 6.56kW solar PV system (16x 410W panels) inst...
By Rob of York , 3 days ago
-
RE: Where heat loss surveys seem to go against practical reality
@cathoderay @jamespa I've managed to get some nice re...
By Rob of York , 4 days ago
-
RE: 7kW EV Charger Options Advice
Doh, not sure that I was thinking straight there, less ...
By Rusty , 4 days ago
SPONSORS
