Last seen: Jul 4, 2025
Hi, Your flow rate of 21L/min is fine, I would turn down the pump to 4 and recheck the flow rate, that will help with dT, you could probably dro...
@iancalderbank that’s why I mentioned it as it didn’t seem that you under stood it correctly. You can be on Intelligent and fixed outgoing I’ve been...
@iancalderbank I'm on Intelligent as well and have FIT from 2015 which had deemed export at 50% but only paid 6p/kwh, so I gave up my deemed export at...
The cycling is probably due to different rooms calling for heat at different times so you have a very small amount of water being heated as only some ...
I think I’ve said it before but mine will cycle anything below 32C. The difference between flow temp and house temp is too small and your emitters ca...
@sarah Hi this is because the flow temp for that room is too low, that’s why I suggested moving the curve up to +3 and see where it stabilises
@sarah on the front menu when your in WC mode you should see +\- symbols these adjust your set curve up and down. Rather than adjusting your curve yo...
So it’s about right How long do you run it for? Eg mine came on at 12pm today it’s been running for 6 hours at 33C and the temp downstairs has incr...
So your flow and return are 34 and 32 outside is 4C if you go to 4C on your WC curve what should the temperature be? If that is 33 or 34 the heat pum...
Yes you are correct but room temp is the temp of the location where that controller is. Is it currently heating hot water as flow and return aren’t ...
@sarah With the pump set to 5 the flow rate you are achieving is too low for the heat pump to be working correctly, it won't be transferring enough he...
In the Eng menu there is a pump speed setting from 1 to 5. What is yours set to. If you increase it and go back to the running info what does the flo...
Latest Posts
-
RE: Compressor attempts start but fails - Nibe Fighter 2005 8kW
@skyefarmer great you located the source of the issue a...
By Mars , 3 hours ago
-
RE: Location of hot water isolation valve on cylinder
@rossowheels if you isolate the water supply in it will...
By ASHP-BOBBA , 12 hours ago
-
RE: Ecodan consuming 100kwh per day in new build!!!
From what you say about the radiators upstairs it does ...
By JamesPa , 17 hours ago
-
The Importance of Radiator Balancing for Efficient Heating: Introducing the Flow Regulating Valve
It’s fascinating to watch how low-temperature heating i...
By Mars , 20 hours ago
-
@heacol, if you're around, can you please provide some ...
By Mars , 23 hours ago
-
RE: Servicing Hitachi HP in rural Somerset
I'd give GreenGenUK a call or email them: sales@greenge...
By Mars , 23 hours ago
-
RE: Heating coming on when not required
I played with a max heating temp but there is a world o...
By JamesPa , 2 days ago
-
RE: Pressure drop Primary circuit
I've always regarded topping up heating systems as my j...
By JamesPa , 2 days ago
-
RE: Heat pump solutions and/or installer recommendations for France
I’d travel to France for work if you were struggling wi...
By Damon Blakemore , 2 days ago
-
RE: 5 Star Service from Havenwise
That's always a danger with any new good idea, @morgan....
By Majordennisbloodnok , 2 days ago
-
Have your say in the Renewable Heating Hub Awards
It’s time to celebrate the best (and call out the worst...
By Mars , 2 days ago
-
-
RE: Mitsubishi cycling while on chilled water output
@iaack yes there's no denying that cold air sinks! I s...
By downfield , 3 days ago
-
RE: Weather compensated secondary circuits with Biomass
@andycoo that flooring sounds ideal. Extra volume is ...
By Sune , 3 days ago
-
If you are thinking of heating on the immersion conside...
By JamesPa , 4 days ago
-
RE: Surface mount or bury primaries for heat pump installation?
@tomasmcguinness, I think your best bet would be using ...
By Aventus Eco , 5 days ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
@toodles all depends on asking the right questions! And...
By Tim441 , 5 days ago
