Forums

Forums
Renewable Heating
Air Source Heat Pum...
Pipe Work Question?
 
Notifications
Clear all

Pipe Work Question?

 
Air Source Heat Pumps (ASHPs)
Last Post by KenBone 1 year ago
6 Posts
4 Users
3 Reactions
1,831 Views
RSS
 EcoBaker
(@ecobaker)
Estimable Member Member
Joined: 1 year ago
Posts: 44
Topic starter 22/03/2024 7:01 pm  

I'm in that common situation where after having a heat pump installed and the performance isn't great, I've dived into youtube and forums like this only to realise that maybe my installer didn't design/install/set up the system particularly well.

I'm in a good situation that I still owe them over £600 for some of the work, which means I can hold that over them. The question I have is about the main pipe work for the flow and return from the HP unit. I have a 3.5m section in my loft that is plastic 22mm pipe, not copper like all the other pipe work. I understand that this will have reduced internal diameter and thus flow, maybe costing me efficiency. Should I hold back final payment and insist this is changed (along with a few other niggles I've found) or is it minor enough not to worry about?

(should add Samsung Gen6 8kw, on two bedroom victorian mid terrace)

This topic was modified 1 year ago by EcoBaker

Samsung Gen6 8kw ASHP in a two bed victorian mid terrace.


   
Quote
bontwoody
 bontwoody
(@bontwoody)
Noble Member Contributor
Joined: 3 years ago
Posts: 836
23/03/2024 12:29 am  

I think the 22mm plastic pipe might be a bit small for 8kw. 22mm copper is considered ok for 5kW I think. This link gives more detail. https://www.heatgeek.com/does-my-pipework-need-upgrading-for-a-heat-pump-with-cheat-sheet/

House-2 bed partial stone bungalow, 5kW Samsung Gen 6 ASHP (Self install)
6.9 kWp of PV
5kWh DC coupled battery
Blog: https://thegreeningofrosecottage.weebly.com/
Heatpump Stats: http://heatpumpmonitor.org/system/view?id=60


   
👍
1
ReplyQuote
Mars
 Mars
(@editor)
Illustrious Member Admin
Joined: 5 years ago
Posts: 3385
23/03/2024 9:08 am  

The issue with the 22mm plastic piping in your loft could potentially impact the efficiency of your heat pump system, especially if it differs from the rest of your installation in terms of diameter. We have this issue where the previous owners “narrowed” the pipework when they extended the heating to the north end of the house, creating a bottleneck which I think is the major issue that the rads at the far end of the house struggle.

Did your installers run all the pipework for your system - copper and the 3.5m run in the loft?

Pre-order: The Ultimate Guide to Heat Pumps

Subscribe and follow our Homeowners’ Q&A heat pump podcast


   
👍
1
ReplyQuote
 EcoBaker
(@ecobaker)
Estimable Member Member
Joined: 1 year ago
Posts: 44
Topic starter 23/03/2024 9:22 am  

@editor Yes so the pipe work from the HP that runs externally to the loft is copper, then the pipe work runs length of loft to the other end where the DHW tank is, that section inside the loft is plastic. I need to measure accurately to check diameters, but im fairly certain that it’s the same as the copper pipes. 

Thinking about it now, all l the pipe work externally from the HP is insulated, I’ve assumed it copper, but don’t know for sure, I might have to check that.

Samsung Gen6 8kw ASHP in a two bed victorian mid terrace.


   
ReplyQuote
bontwoody
 bontwoody
(@bontwoody)
Noble Member Contributor
Joined: 3 years ago
Posts: 836
23/03/2024 11:43 am  

There is a good video explaining the pipe sizing issue here

https://renewableheatinghub.co.uk/forums/postid/29119

 

House-2 bed partial stone bungalow, 5kW Samsung Gen 6 ASHP (Self install)
6.9 kWp of PV
5kWh DC coupled battery
Blog: https://thegreeningofrosecottage.weebly.com/
Heatpump Stats: http://heatpumpmonitor.org/system/view?id=60


   
ReplyQuote
 KenBone
(@kenbone)
Trusted Member Member
Joined: 2 years ago
Posts: 34
24/03/2024 10:54 pm  

Posted by: @ecobaker
↑

I'm in that common situation where after having a heat pump installed and the performance isn't great, I've dived into youtube and forums like this only to realise that maybe my installer didn't design/install/set up the system particularly well.

I'm in a good situation that I still owe them over £600 for some of the work, which means I can hold that over them. The question I have is about the main pipe work for the flow and return from the HP unit. I have a 3.5m section in my loft that is plastic 22mm pipe, not copper like all the other pipe work. I understand that this will have reduced internal diameter and thus flow, maybe costing me efficiency. Should I hold back final payment and insist this is changed (along with a few other niggles I've found) or is it minor enough not to worry about?

(should add Samsung Gen6 8kw, on two bedroom victorian mid terrace)

 

That's too tight IMO, we would use 28mm copper, or 32mm MLCP

 

 

Technical Manager & Professional Installer: Ultimate Renewables


   
👍
1
ReplyQuote



Forum Jump:
  Previous Topic
Next Topic  
Share:

Join Us!

Podcast Picks

Latest Posts

Members Online

Click to access the login or register cheese
x Powerful Protection for WordPress, from Shield Security
This Site Is Protected By
ShieldPRO →