Best base for 6kW Ecodan heat pump external unit
What is everyone's thoughts on installation of a unit on earth/ground - seems to be a few schools of thought, around:
Base materials:
- level poured concrete - either of:
- one base
- two separate bases/'plinths'
- paving slab
- gravel
Beneath unit's feet:
- nothing - feet sit on concrete/slab
- 'flexi foot' (e.g. 600mm longh) with struts
- anti-vibration mounts under each foot
Securing:
- feet bolted directly to concrete/slab
- feet bolted to flexi foot and either of:
- flexi feet sat unsecured on top of concrete/slab/gravel
- flexi feet bolted / strapped to / otherwise secured to concrete/slab
- feet bolted to mounts, mounts bolted to concrete/slab
Mitsubishi installation manual says two concrete plinths with feet bolted directly to them.
It feels to me that two concrete plinths with unit feet secured to rubber and then rubber secured to concrete is best - the thinking with the last part: to avoid any small unit movements which may impact balance / create internal vibrations or cause small pipework vibrations downstream (unless flexi hoses always cancel this out?).
Do people think securing the rubber to the plinths would bring any benefits (even if small), and if so, which way would you go if you were doing a fresh install?
I would say always always always mount on thick rubber anti-vibration grommets in any domestic setting. You do not want to go through it all to find bzzzzzzzzz through your home. I think the new MIS3005 might give some advice on this when released after the consultation as, presently, anti-vibration mounting is required on installations by MCS but a worrying loop hole is the there is zero guidance on what is appropriate. You could literally put something for the weekend 'twixt the unit and concrete base/wall bracket and could pretend that is the anti-vibration mounting.
Ahh I might be wrong about there being a requirement for AV grommets if the manual says bolt directly to a concrete base. The requirement in MIS3005 is "4.4.4 Anti-vibration pads/mats/mounts and flexible hose connections should be installed according to the manufacturer’s instructions to reduce the effects of vibration on the building structure." This mixes the expectation there should be AV grommets with the requirements in the installers manual, and if no requirement specified then I supposed they are not strictly required under MCS.
Posted by: @eltonI would say always always always mount on thick rubber anti-vibration grommets in any domestic setting. You do not want to go through it all to find bzzzzzzzzz through your home. I think the new MIS3005 might give some advice on this when released after the consultation as, presently, anti-vibration mounting is required on installations by MCS but a worrying loop hole is the there is zero guidance on what is appropriate. You could literally put something for the weekend 'twixt the unit and concrete base/wall bracket and could pretend that is the anti-vibration mounting.
I have found that 'something for the weekend' doesn't actually normally stop 'vibration'. 😋
@rhh2348 here's what we did with our heat pump. We secured our heat pump (weighing around 180kg) by placing four levelled concrete slabs side-by-side for a stable base.
Buy Bodge Buster – Homeowner Air Source Heat Pump Installation Guide: https://amzn.to/3NVndlU
From Zero to Heat Pump Hero: https://amzn.to/4bWkPFb
Subscribe and follow our Homeowners’ Q&A heat pump podcast
Posted by: @eltonI would say always always always mount on thick rubber anti-vibration grommets in any domestic setting.
Can you give an example or two of such items, and explain why those?
You do not want to go through it all to find bzzzzzzzzz through your home.
Indeed - hence the thread question 🙂
Posted by: @eltonAhh I might be wrong about there being a requirement for AV grommets if the manual says bolt directly to a concrete base.
I did think it odd, particularly as my install came with flexi feet! Also, Mitsubishi do list those feet in their accessories.
The requirement in MIS3005 is "4.4.4 Anti-vibration pads/mats/mounts and flexible hose connections should be installed according to the manufacturer’s instructions to reduce the effects of vibration on the building structure." This mixes the expectation there should be AV grommets with the requirements in the installers manual, and if no requirement specified then I supposed they are not strictly required under MCS.
Understood, however I am looking for the optimal approach. What have you done / what would you do again if you did afresh?
Posted by: @editor@rhh2348 here's what we did with our heat pump. We secured our heat pump (weighing around 180kg) by placing four levelled concrete slabs side-by-side for a stable base.
-- Attachment is not available --
-- Attachment is not available --
Wow!
Are they on earth below?
What's the layers between your ASHP and the slab? (e.g. I think I can see rubber feet under the cabinet / enclosure)
@rhh2348, yeah on earth below, but the area was very heavily compacted so even trying to burrow them in was quite hard.
Not a huge gap bewteen the ASHP and the slab. It's running now and I'm out tomorrow but I can measure on Wednesday. It is standing in rubber feet. There is zero vibration noise from this unit. It's rock solid.
Base drawing from our manufacturer.
Buy Bodge Buster – Homeowner Air Source Heat Pump Installation Guide: https://amzn.to/3NVndlU
From Zero to Heat Pump Hero: https://amzn.to/4bWkPFb
Subscribe and follow our Homeowners’ Q&A heat pump podcast
Posted by: @editorIt is standing in rubber feet. There is zero vibration noise from this unit. It's rock solid.
Niiice. Which feet did you go for and (how) are they secured to the slabs and enclosure / unit?
@rhh2348 it's the way the heat pump arrived. It was literally taken off a truck, wheeled to the slabs and placed there. It's designed to stand (it's taller than me, and I'm over 6-foot), so no option of wall mounting. Because of it's tall design it's very well balanced, and even when running full tilt, it never reverberates or shakes. Prior to hearing form other homeowners we never even knew that reverberations were a "thing" when it came to heat pumps.
Buy Bodge Buster – Homeowner Air Source Heat Pump Installation Guide: https://amzn.to/3NVndlU
From Zero to Heat Pump Hero: https://amzn.to/4bWkPFb
Subscribe and follow our Homeowners’ Q&A heat pump podcast
Posted by: @editoryeah on earth below, but the area was very heavily compacted so even trying to burrow them in was quite hard.
This comment has me thinking whether adding concrete/slabs may introduce the possibility of vibrations, when some flexi feet (to raise off ground) on level compacted earth (maybe even sat within a 10mm recess with small drain channel out) may do the job as well if not better...
- 26 Forums
- 2,104 Topics
- 46.3 K Posts
- 99 Online
- 3,393 Members
Join Us!
Latest Posts
-
Cooling with Samsung Gen6 and Flow error
HI I've got a Samsung gen6 ASHP, which I am trying to...
By EcoBaker , 43 seconds ago
-
RE: Ripped Off: How UK Homeowners Are Paying Gas Prices for Wind Energy
Short video from Greg on the announcement
By Jeff , 15 hours ago
-
@bart That is terrible and a clear breach of the buildi...
By Brendon Uys , 16 hours ago
-
RE: BUS Grant: removal of all other fossil fuel heat sources
@editor If it is of any interest, we had the BUS grant,...
By Toodles , 23 hours ago
-
Sorry to hear that @bruce. Sadly I’ve heard from multip...
By Mars , 1 day ago
-
RE: Crystal Ball Time: Communal or even Area Energy Storage?
I am invested in a couple of listed energy storage fund...
By Old_Scientist , 1 day ago
-
RE: Who's your electricity provider and what's your tariff?
That would be my biggest commitment -time to gain great...
By SUNandAIR , 2 days ago
-
RE: Who has a V2G EV installation
As has been discussed on other threads, trying to justi...
By Majordennisbloodnok , 2 days ago
-
RE: Aira Heat Pump: Stylish Scandinavian Heating
Thanks @mikeh. Then I will also go back to non smart ta...
By ChandyKris , 3 days ago
-
RE: Location of hot water isolation valve on cylinder
@transparent Thank you so much and very helpful. Earlie...
By rossowheels , 3 days ago
-
RE: Ecodan consuming 100kwh per day in new build!!!
It does indeed look like that, @skyefarmer. There is ...
By Majordennisbloodnok , 4 days ago
-
RE: Plug and play solar. Thoughts?
Have a read of my previous posts on so-called Balcony S...
By Lucia , 5 days ago
-
RE: Compressor attempts start but fails - Nibe Fighter 2005 8kW
"To tell you the truth, I don't know if HAL is homicida...
By Scalextrix , 5 days ago
-
The Importance of Radiator Balancing for Efficient Heating: Introducing the Flow Regulating Valve
It’s fascinating to watch how low-temperature heating i...
By Mars , 6 days ago
-
RE: Servicing Hitachi HP in rural Somerset
I'd give GreenGenUK a call or email them: sales@greenge...
By Mars , 6 days ago
-
RE: Heating coming on when not required
I played with a max heating temp but there is a world o...
By JamesPa , 6 days ago
-
RE: Pressure drop Primary circuit
I've always regarded topping up heating systems as my j...
By JamesPa , 6 days ago