Forums

Forums
Renewable Heating
Air Source Heat Pum...
Air source heat pum...
 
Notifications
Clear all

Air source heat pumps and noise

 
Page 7 / 7
Air Source Heat Pumps (ASHPs)
Last Post by newhouse87 8 months ago
80 Posts
15 Users
43 Reactions
7,496 Views
RSS
Toodles
 Toodles
(@toodles)
Illustrious Member Contributor
Joined: 3 years ago
Posts: 1979
20/10/2024 3:54 pm  

@newhouse87 They would sit on the raised pad or base and the heat pump will be bolted with C clamps as @transparent indicated to the rails. The weight of the pump is sufficient to keep the whole assembly from shifting. Regards, Toodles.

Toodles, he heats his home with cold draughts and cooks his food with magnets.


   
👍
1
ReplyQuote
Transparent
 Transparent
(@transparent)
Illustrious Member Moderator
Joined: 3 years ago
Posts: 2418
20/10/2024 4:02 pm  

Yes. If 400-450mm is adequate for the distance between the feet positions on your ASHP, then those are fine.

Most people don't bolt them down...
.... whilst a few put a bolt straight through the steel channel and the rubber mass, then into the concrete pad below
which somewhat defeats the whole point of its vibration absorbing properties! 🤨 

If you look closely, there's a recess along each side of the foot.
That's the location where it can be held.

BoltFoot

Either drill a hole and insert a long bolt at an angle (as shown in purple),
or else use a steel angle (orange) and a vertical bolt (blue).

Save energy... recycle electrons!


   
👍
1
ReplyQuote
 newhouse87
(@newhouse87)
Reputable Member Member
Joined: 2 years ago
Posts: 231
20/10/2024 4:13 pm  

Think it should be bolted down as it will be on raised pad though. V strong winds here at times particularly today.

Good to know it can be done without needed ex pensive plumber and spark back to extend wiring and lines. Could not sleep in bedroom it's currently attached to when running in winter.


   
ReplyQuote



Transparent
 Transparent
(@transparent)
Illustrious Member Moderator
Joined: 3 years ago
Posts: 2418
20/10/2024 4:29 pm  

If I was going to make my own galvanised steel clamps to hold the feet in place,
then I'd start with some roofing straps.

image

There are two gauges.
The thicker one is about 5mm, which means I have to use a vice and lump-hammer to re-form the angles.

Alternatively, in these far-western realms of England, we still have blacksmiths who will create whatever you wish for 😀 

Save energy... recycle electrons!


   
ReplyQuote
 Judith
(@judith)
Prominent Member Member
Joined: 2 years ago
Posts: 363
22/10/2024 6:25 pm  
GPID_1100640612_TECH_00.pdf

This is the bracket supporting our 7kW Vaillant. It looks more substantial and is designed for an higher upper weight limit and has no noise we’ve heard so far, not even on the legionnaires cycle.

IMG 3201
This post was modified 8 months ago by Judith

2kW + Growatt & 4kW +Sunnyboy PV on south-facing roof Solar thermal. 9.5kWh Givenergy battery with AC3. MVHR. Vaillant 7kW ASHP (very pleased with it) open system operating on WC


   
👍
1
ReplyQuote
Transparent
 Transparent
(@transparent)
Illustrious Member Moderator
Joined: 3 years ago
Posts: 2418
22/10/2024 7:21 pm  

Interesting photo of that bracket @judith  😀 

That looks to be the version of the Vaillant bracket for walls with external insulation.
It uses 68mm discs to pass the bolt through the outer insulation layer.

The bolt itself is 'glued' to the solid wall beyond the insulation layer using the Hilti HIT-HY-170 chemical anchor.
It's a resin and hardener compound which gets mixed by the flutes on the inside of the nozzle as it gets injected into a pre-drilled hole.

The downside of your installation seems to be the gap left around the 20mm corrugated-plastic conduit which supplies the electricity.
That will need sealing with a low-modulus mastic to prevent ingress of rain.

 

Save energy... recycle electrons!


   
ReplyQuote
 Judith
(@judith)
Prominent Member Member
Joined: 2 years ago
Posts: 363
22/10/2024 9:05 pm  

@transparent it has a virtually clear seal that can barely be seen by eye never mind on a photo. I’ve not proded it (calibrated biro test!) so I’m not sure of the modulus

We’ve got external insulation so it’s the right version of the bracket for us.

This post was modified 8 months ago by Judith

2kW + Growatt & 4kW +Sunnyboy PV on south-facing roof Solar thermal. 9.5kWh Givenergy battery with AC3. MVHR. Vaillant 7kW ASHP (very pleased with it) open system operating on WC


   
👍
1
ReplyQuote
 newhouse87
(@newhouse87)
Reputable Member Member
Joined: 2 years ago
Posts: 231
22/10/2024 9:10 pm  

Similar bracket to mine but i have no external insulation. Would the external insulation be the reason you have no vibration noise?


   
ReplyQuote
Page 7 / 7
Forum Jump:
  Previous Topic
Next Topic  

Currently viewing this topic 1 guest.

Share:

Join Us!

Login   Register

Trusted Installers

Struggling to find a reliable heat pump installer? A poor installation can lead to inefficiencies and high running costs. We now connect homeowners with top-rated installers who deliver quality work and excellent service.

✅ Verified, trusted & experienced installers
✅ Nationwide coverage expanding
✅ Special offers available

👉 Find your installer now!

Latest Posts