
Last seen: Sep 25, 2025
Oh dear, censorship. I know, I know, but as long as you are sure of your facts, and that is an absolute requirement, you need have no fear of libel (s...
I think it rather depends on what one is trying to achieve. My two main objectives (others will have different objectives, and so different solutions)...
I've just tested writing to the Midea wired controller using minimalmodbus to see if I can do it without blowing up the whole shebang and it seems all...
I'm sorry, I am not sure what you are getting at here. They are meant to be images, images that show the appearance of the panels, not intended to be ...
Yes, sooner or later that will happen, the question is when not whether, but so far my heat pump has been remarkably well behaved, and so far has run ...
Once I've got the read side of things sorted, I will start experimenting with set back and boost, but it may have to wait until next autumn/winter, as...
Complexity, dear boy, complexity! You'll be dancing with the three legged one eyed unicorn before you know it! Basic python plus minimalmodbus can do ...
In Midea-speak, though I have yet to even get near to do this, I had in mind tweaking the weather comp set points to achieve this: to get a 2 degree b...
All so very true... Obfuscation. Why use one line when you can use two hundred? Here's my entire hourly data extracted from minute data code, based ...
Worth mentioning that a load adjusted weather compensation curve was, and still is, one of my objectives in all this, primarily so I can set an overni...
@iancalderbank and @derek-m - I agree with both of you. This thread has unintentionally turned into something of a monster, perhaps not yet Frankenst...
@batalto - the above is a one off reading, it will be interesting to see whether the Midea figures always round downwards once I have a series of read...
- 26 Forums
- 2,183 Topics
- 48.1 K Posts
- 34 Online
- 5,756 Members
Join Us!
Podcast Picks
Latest Posts
-
RE: Samsung Gen 6 - Schedules not working
@old_scientist Thanks. I'll check the FSVs tomorrow. Ye...
By bontwoody , 30 minutes ago
-
RE: DNO export limit problems.
So you're planning to add a PW3 to the existing setup (...
By Old_Scientist , 32 minutes ago
-
Moving FIT array onto a Tesla Powerwall 3 possible?
I currently have a 3.68kw inverter hooked up to 4kwp of...
By AdamK , 58 minutes ago
-
It's currently a 5kW/15kWh Libbi, as we're homeworkers ...
By wully , 2 hours ago
-
RE: Do I just go with the lowest quote for my heat pump?
@toodles I have electric pet blankets 🙄 If req...
By Jancold , 2 hours ago
-
RE: Flexi-Orb Heat Pump Scheme: A Game-Changer for the UK's Heat Pump Industry
Signed
By Judith , 3 hours ago
-
RE: Which thermostat should I get (or do I need one?)
Whether you need a separate thermostat for your UFH hea...
By Judith , 3 hours ago
-
@drei just a small detail on your table posted on the 2...
By Judith , 3 hours ago
-
RE: Large heat pump options for church building
I should think that a heat loss calculation might be a ...
By Toodles , 4 hours ago
-
RE: Say hello and introduce yourself
I've started a topic in the Heating Alternatives sub-fo...
By wully , 6 hours ago
-
@toodles Im trying my best but it is getting a tad tedi...
By bontwoody , 6 hours ago
-
RE: Seal the Deal: Don't Let Your Heat Pump Leak Energy
Indeed. If the primaries are not big enough to carry th...
By Old_Scientist , 10 hours ago
-
RE: Clivet ASHPs and weather compensation
It sounds like weather comp may not be activated. Give ...
By Simon Wardle , 13 hours ago
-
RE: Help me keep the faith with my air source heat pump installation
I just looked at mine. My flexis (which run horizontal...
By JamesPa , 15 hours ago
-
RE: Air source heat pump roll call – what heat pump brand and model do you have?
Manufacturer: Vaillant Model: Arotherm Plus 7kW Typ...
By MatWin , 1 day ago
-
@papahuhu Sounds as though you need to speak to your in...
By Toodles , 1 day ago
-
I ‘did the math’ for Nov. to the end of April to be on ...
By Toodles , 1 day ago
-
RE: Testing new controls/monitoring for Midea Clone ASHP
@tasos automations on Home Assistant so if there is a p...
By benson , 1 day ago
-
RE: Sizing - Save me from my headache
Mitsi 8kW has a 6kW variable and 2kW fixed compressor s...
By JamesPa , 2 days ago