Battery Charging Anomalies
sorry for any confusion - it was the only reference I could find to charging and temperature!
I don’t think you are alone @dunlorn there are two people in our village with solar/battery systems - not puredrive and they report the same problem. Both are convinced it is temperature related.
One has apparently surrounded the batteries with Kingspan insulation and says that it fixed the problem.
To be clear - above is NOT advice. It does show others have similar issue. I’d be chasing installer, solis and pure drive for answers. Someone wrote some code- they must know how the charging current is set and if what you are experiencing is ‘expected’ behaviour.
Our experiences with solar pv, ASHP, battery, and EV: ourhomeelectric.co.uk
@dunlorn the BMS (electronics) in each battery will have at least one temperature sensor. Maybe more.
Can you actually see what they read when using the App?
I'm still not convinced that the battery temperature is too low once the sun has been up a few hours.
But there is a possibility that a temperature sensor isn't in the right place...
... or that it's become disconnected from the BMS.
If so, it's a simple job of clipping it back in!
Save energy... recycle electrons!
Thanks all. This is useful insight and, yes, I am in discussion with the installer about this. He in turn is chasing Solis and Puredrive. I'll post any update once I get something meaningful.
I can't access any temperature info from the app unfortunately, although - to Derek's point - I do wonder if the battery internals are a few degrees below ambient, especially since the batteries are sited on a north facing elevation in shadow. I too am contemplating building a small insulated enclosure so pleased to hear it fixed things for someone else. I'll definitely ask the question about the temperature sensor though.
2 x 12kW Samsung Gen6 ASHP, 5.6kW solar PV ground mounted c/w 10kWh Puredrive battery & Solis inverter.
I think it would be helpful if you had an independent method of measuring temperature.
Look at this £6 unit from Amazon
Having the 'external' sensor on the end of a wire means that you can place it inside a battery case, but still read the temperature from the display outside.
The only precaution I'd take is to place a thin layer of PVC insulation tape around the metal sensor, just in case it should fall across two internal contacts!
Or, of course, you could use PVC tape to hold it in a particular position inside the battery box.
For anyone else watching this, who isn't in a hurry, you can get these temp-sensors very much cheaper if you buy direct from China.
There are variations on the length of lead and whether you also want to measure humidity.
Save energy... recycle electrons!
In my day job I'm designing systems that support fire-rated battery rooms with 200kVA Siemens Bluevault Li-Ion 230V UPS batteries. They require a room temperature between 15-25degC, the optimal is 20degC. That's common for most Li-Ion tech. Manufacturer's data may give a wider range for both storage and use, but the BMS may limit their charge and discharge current rating. This is well known for both Li-Ion and Ni-Cad batteries.
One of the problems with solar PV installers or DIY-ers locating batteries in, say, attics or garages, is that they can be subject to very wide ambient summer and winter temperature variations, and that will limit their functionality and performance at both ends.
@allyfish thanks for that.
”This is well known for both Li-Ion and Ni-Cad batteries.”
Wish it was. Nothing about charge rate vs temperature in any of the domestic battery brochures/specs I’ve scanned. And as you say batteries are being installed in attics and garages and even outside up and down the country.
Ho hum
Our experiences with solar pv, ASHP, battery, and EV: ourhomeelectric.co.uk
Most days I find that a comment on this forum provokes me to do a bit of research. Today it's the turn of @allyfish 🙂
It seems that Seimens BlueVault batteries are using Li-MNC chemistry, and are substantially marketed to the marine industry.
Does that mean they're Seamen's batteries? 😉
I don't know what model @allyfish is using, but the general format utilises liquid-cooled enclosures, each containing nine battery modules.
There's an excellent technical 'briefing' by Ketil Aagesen, Head of BlueVault Technology at Siemens Energy, which is worthwhile reading on LinkedIn.
The main reason he gives for a temperature controlled environment is to avoid shortening the 'life' of the battery. That is well documented, but LiMNC chemistry (Manganese, Nickel, Cobalt) is still used extensively for Electric Vehicles due to its capacity/mass ratio. That allows EVs to accelerate quickly and offer longer range between recharging.
The same is not the case for most domestic home-storage batteries.
Commercial and DIY installations in the home are using LiFePO4 chemistry.
Yes, the capacity is lower per Kg, but few of us are worried about the lack of acceleration in our houses.
Equally, many end-users would like to avoid a lithium chemistry which utilises Cobalt.
Not only can it have damaging effects on the environment, but its mining operations are marred by gangs and modern-slavery.
Guidance from manufacturers states that LiFePO4 technology shouldn't be charged below 0°C, but that doesn't prevent their widespread deployment in camper-vans, mainly in USA.
Installations below 0°C generally use BMS units which incorporate a heating control port, such as the JK B2A8S20PH from Jiakong.
Within a couple of years I expect to see much wider use of Lithium Titanate (LTO) cells for sub-zero static locations.
They have yet lower capacity, and their output is only 2.3v per cell. But they can be charged at -20°C without loss of performance or lifetime degradation.
LiFePO4 and LTO chemistry are much more stable than LiMNC.
They can be damaged by direct physical attack, but they produce far less heat and arcing.
As such, they are better suited for domestic installation.
Save energy... recycle electrons!
- 26 Forums
- 2,136 Topics
- 46.8 K Posts
- 26 Online
- 5,662 Members
Podcast Picks
Latest Posts
-
RE: Rodents! A word of warning for heat pump owners
The gaps and holes have reduced on heat pumps over the ...
By dgclimatecontrol , 5 minutes ago
-
RE: Ecodan & MelCloud scheduling
I couldn't agree more. I might go so far as to change t...
By Majordennisbloodnok , 11 minutes ago
-
RE: Air source heat pump roll call – what heat pump brand and model do you have?
Forum Handle: EGP01 Manufacturer: Samsung Model: 8K...
By EGP01 , 3 hours ago
-
Thanks for the heat geek info. I've fitted my own heat ...
By bontwoody , 5 hours ago
-
RE: Does anyone have experience of a smart water meter?
Just to give a sense of scale, I've used the CCW water ...
By Majordennisbloodnok , 6 hours ago
-
-
RE: Powerwall 3 or Myenergi or something else?
We have a Tesla Powerwall 3, recently installed, so I m...
By Old_Scientist , 1 day ago
-
RE: Mitsubishi PAR-WT60R-E Wireless Controller installation
@morgan They have been paired once but it was thought b...
By DavidAlgarve , 2 days ago
-
RE: Isolating the system for a planned power cut
A great many ground-mounted local substation transforme...
By Transparent , 2 days ago
-
RE: Heat Pump Servicing & Maintenance – Good Value or Rip-Off?
Having bit the bullet and paid £250 for a service, our ...
By Old_Scientist , 3 days ago
-
New heat pump heating system underperforming in Italy... Advice needed!
hi all, first post! I've just renovated a house in sout...
By robinlawrie , 3 days ago
-
RE: Anyone still weathering it out with Agile?
I went to Agile when I had solar installed July last ye...
By NJT , 4 days ago
-
RE: Mitsu Wireless Controller and MelCloud
Well it has now become obvious that the installation of...
By DavidAlgarve , 4 days ago
-
RE: Say hello and introduce yourself
Whilst you're busy installing services (pipes and wires...
By Transparent , 5 days ago
-
RE: New Vaillant aroTherm Plus in black - When will it come to the UK?
@editor I know it was formally announced at Ish the oth...
By PatrickVito , 6 days ago
-
@moman0311 welcome to the forums. I've received your em...
By Mars , 6 days ago
-
RE: Thermostat for Ideal Logic Air with 3 zone support
No harm at all in plumbing it as 3 zones, I would have ...
By JamesPa , 1 week ago
-
RE: ASHP heat output monitoring
@carlo I see there is a discussion in Facebook user gro...
By Tim441 , 1 week ago
-
RE: Flexi-Orb Heat Pump Scheme: A Game-Changer for the UK's Heat Pump Industry
MCS have set a potential trap in the new version of MCS...
By JamesPa , 1 week ago
-
RE: Who has a V2G EV installation
General comment on battery care... I guess if ev is on ...
By Tim441 , 1 week ago