
Last seen: Aug 19, 2025
@broadsman - I think you should also consider a partial DIY approach. Elsewhere on this forum we've discussed the battery enclosures made by Seplos,...
Whether you decide to manually release air from an 'automatic' valve rather depends on how much air is in the system, and what amount of exercise you ...
The incomer cable probably only has a size-rating once every meter.The OF 462-467 doesn't give me enough information without also knowing the cable ma...
Yes, I noted that your first post on this topic said But I'm unsure whether it was 'working well' because it was relatively easy to push through ...
Have a closer look and see whether these are tight elbows or swept bends. You might also want to view the comparison between smooth bends and ...
We also ought to consider if the flow is being reduced by sharp elbow joints in the pipework. There is a considerable loss of pressure if standard ...
That's a very useful photo @jancoldIt provides me with heaps of issues which need a comment! 1: The "new" Service Fuse must've been installed by...
The board on which you have the Service Fuse and Meter shouldn't be used for other equipment. I don't see how a separate (small) consumer unit could...
The height of a Smart Meter is 175mm including the Communications Hub. It will need at least 60mm below it to accommodate the bend in the tails. ...
You're contemplating staying cold until Spring?! Is the reason that you can't get your hand to the valve because of the close proximity of the pipes...
Then there's likely to be more air in the pipes somewhere. The amount of air which came out from that bleed position was "a fair bit", but it's limi...
Just before we jump to the conclusion that the pump is effectively "full on", there are occasions when a pump must be put into that mode so that its s...
- 26 Forums
- 2,134 Topics
- 46.8 K Posts
- 88 Online
- 5,661 Members
Join Us!
Podcast Picks
Latest Posts
-
I'm curious as to what the heat geek response is Mars. ...
By bontwoody , 1 hour ago
-
RE: Anyone still weathering it out with Agile?
I went to Agile when I had solar installed July last ye...
By NJT , 15 hours ago
-
RE: Does anyone have experience of a smart water meter?
Yes, I was aware the “smart” part is the same tech used...
By Majordennisbloodnok , 15 hours ago
-
RE: Mitsu Wireless Controller and MelCloud
Well it has now become obvious that the installation of...
By DavidAlgarve , 1 day ago
-
RE: Heat Pump Servicing & Maintenance – Good Value or Rip-Off?
@heat-pump-newbie as I suspected. I measure/monitor my ...
By Old_Scientist , 2 days ago
-
RE: Say hello and introduce yourself
Whilst you're busy installing services (pipes and wires...
By Transparent , 2 days ago
-
RE: New Vaillant aroTherm Plus in black - When will it come to the UK?
@editor I know it was formally announced at Ish the oth...
By PatrickVito , 3 days ago
-
@moman0311 welcome to the forums. I've received your em...
By Mars , 3 days ago
-
RE: Thermostat for Ideal Logic Air with 3 zone support
No harm at all in plumbing it as 3 zones, I would have ...
By JamesPa , 4 days ago
-
RE: ASHP heat output monitoring
@carlo I see there is a discussion in Facebook user gro...
By Tim441 , 4 days ago
-
RE: Flexi-Orb Heat Pump Scheme: A Game-Changer for the UK's Heat Pump Industry
MCS have set a potential trap in the new version of MCS...
By JamesPa , 5 days ago
-
RE: Who has a V2G EV installation
General comment on battery care... I guess if ev is on ...
By Tim441 , 6 days ago
-
@old_scientist like for like comparisons are almost imp...
By Tim441 , 6 days ago
-
RE: Who's your electricity provider and what's your tariff?
@old_scientist There is an option in the Tesla app that...
By Toodles , 6 days ago
-
RE: Octopus Cosy & Octopus EV + bidirectional smart tariff, together. What, eh?
@old_scientist me too. Just installed my new heat pump ...
By Eliuccio , 1 week ago
-
RE: Is your heat pump insured?
Yup just spoke to Privilege to inform them of my impend...
By Scalextrix , 1 week ago
-
RE: Forum updates, announcements & issues
Just to keep everyone in the loop, as the site continue...
By Mars , 1 week ago
-
RE: Fast DHW setting on Midea (Clivet) heat pump
@simon-w, is this something you could potentially assis...
By Mars , 1 week ago
-
RE: Share Your Experiences with Heat Pump Manufacturer Support
Fwiw I called my installer out for the first time a few...
By JamesPa , 1 week ago
-
RE: Long term efficiency degradation
@jamespa yes as I thought thanks. We have a reaso...
By Scalextrix , 1 week ago