Last seen: Apr 28, 2024
@gary Thanks. I'm emboldened to give it a go!
Derek et al, Sorry for resurrecting this slightly old thread, but I'm now back at the property in question after a time away. When I attempt to acce...
👍 Thanks SUNandAIR.
Thanks HarriUp. The COP figure of 6 was calculated from Energy out/Energy in, as displayed of the FTC6, but I'm not sure how accurate that is. Ma...
Thanks. Not sure about mixing valves. But when I ran my system on the manually set curve, I had it at 32C when outside temp was 0, and 21C was outsid...
@ajdunlop Thanks for this. I'll give it a try. At around the same location in the menu there's the option to alter the min and max flow temperature ...
@derek-m Thanks Derek, I managed to download a manual where it states that the 'interval' default is 10 minutes, but can be increased to a max of 6...
@derek-m Thanks. If you're able to point me to where I can do this in the app, I'd be grateful. A.
Thanks Gary for that succinct reply to my rambling question. I'll try it for a bit and see how it goes. It's a shame their isn't an option for eithe...
@editor I didn't resolve the issue really. My system is an Ecodan 5kW. I understand that it might be possible using Melcloud (but I'd need to buy an...
@abernyte Thanks. The installer fitted 3rd party stats (Heatmiser) and 'lost' the Ecodan WiFi interface, so looks like I'll have to purchase both the...
Latest Posts
-
RE: How good is the app support for your heat pump?
Wow, a lot on those boards.. I did get into ESP32 on...
By Batpred , 26 minutes ago
-
RE: How to increase DHW water temperature on Samsung Gen 6 Control Panel
Im just in the process of connecting up my mixergy cyli...
By bontwoody , 5 hours ago
-
RE: Struggling to get above 3.3 on heating
You should be getting better than that at this time of ...
By JamesPa , 8 hours ago
-
Unless anyone can tell me differently, there appears to...
By DowallyDrifter , 8 hours ago
-
RE: Should Our Water Circulation Pump Be Configured to Run All The Time?
I run my Vaillant on either expanded mode (either end o...
By JamesPa , 10 hours ago
-
RE: Twin 10kw Grant Aerona Volumiser Tanks using lots of power
@adam Hi just jumped on this thread as I too have 2 10k...
By bretix , 19 hours ago
-
RE: Help me keep the faith with my air source heat pump installation
on a facebook thread someone has comented to the effect...
By AdamK , 19 hours ago
-
The timing of training and inference are very applicati...
By wully , 21 hours ago
-
RE: Samsung Heat Pump – Can't Activate TW2 Pipe Sensor (for Delta T Control)
Wanted to add an update. As I am running HomeAssistan...
By bubuontheweb , 22 hours ago
-
RE: Grant 13kW Aerona3 - issues getting zones to temp
You are correct you dont need the second pump if there ...
By JamesPa , 22 hours ago
-
RE: New Fogstar 15.5kWh upright solution
From my experience with inverters from different Far Ea...
By Transparent , 23 hours ago
-
@bontwoody Thank goodness you are ‘back on-line’ so to ...
By Toodles , 1 day ago
-
RE: Automation options to maximuse efficiency & ToU tariffs
@majordennisbloodnok Seems reasonable. It would be m...
By Batpred , 1 day ago
-
RE: Havenwise App Help & Forum Support – Get the Most from Your Heat Pump
@hcas OK Thanks. Will do.
By bontwoody , 1 day ago
-
RE: What crazy nonsense are inverter limits and why are they imposed?
@transparent Thank you for a very comprehensive, tim...
By Batpred , 1 day ago
-
RE: Isolating the system for a planned power cut
@transparent 😊 I may have lost you there.. I ...
By Batpred , 1 day ago
-
-
RE: Low COP and unevenly heated rooms with 12kW Samsung AE120MXTPEH / AE260TNWTEH
Where is the noise coming from. If its the pump then p...
By JamesPa , 1 day ago
-
The Mars and Richard Kitchen Show
Just stopping by to say: 1) Mars I'm so sorry that yo...
By Lucia , 2 days ago
-
RE: Electricity price predictions
Without getting too much into politics, given that the ...
By Batpred , 2 days ago
