Recent Posts

| Forums | Topics

Page 15 / 161 Prev Next

Posts with their shortened content
	RE: Help me keep the faith with my air source heat pump installation By AgentGeorge, 1 day ago Forum Air Source Heat Pumps (ASHPs)
	The double panel radiators I’ve seen have a bleed screw on both panels. Usually the nut around the bleed screw can undo allowing it to be replaced. Id take the photo to City Plumbing and show them if ...
	RE: Confused by Flow Rates By Grantmethestrength, 2 days ago Forum Air Source Heat Pumps (ASHPs)
	@editor another great episode, but same as @phil-bell I am now going to have a good look at my flow rate, my lowest flow rate I can get out of my Grant Aerona3 is 28l/min but I think this may not be e...
	RE: Grant 13kW Aerona3 - issues getting zones to temp By Grantmethestrength, 2 days ago Forum Air Source Heat Pumps (ASHPs)
	I have the same unit and controller and it has been a journey of learning to say the least. After a terrible ECO4 install it has taken nearly 10 months to get the system to the point where it is easy ...
	RE: Grant 13kW Aerona3 - issues getting zones to temp By Crimson, 2 days ago Forum Air Source Heat Pumps (ASHPs)
	Unfortunately this is the ONE day this month I can’t even arrange a call due to work commitments at the time. What I’ll do however is ask the other half if the engineer is ok to leave his numbe...
	RE: Help me keep the faith with my air source heat pump installation By AdamK, 2 days ago Forum Air Source Heat Pumps (ASHPs)
	@agentgeorge this is a pic of the bleed valve that’s snapped. It should have a square bleed pin in the centre of that sort of nut insert. Attachment : IMG_1241.jpeg
	RE: Confused by Flow Rates By Mars, 2 days ago Forum Air Source Heat Pumps (ASHPs)
	I’ll defer to @pirate-rich and @nigel-d and @ian-e on this one…
	RE: Havenwise App Help & Forum Support – Get the Most from Your Heat Pump By HCas, 2 days ago Forum Electricity, Tariffs, Monitoring & Providers
	@nickhorne Unfortunately not. We take the "normal" IOG slots into account. But not the ones you get extra outside of the usual times. That's because that information isn't available on the Octopus API...
	RE: Mixture of copper and plastic CH pipework. Will it be ok, or need changing? By JamesPa, 2 days ago Forum Thermostats, Volumisers, Buffer Tanks, TRVs, Pumps, Piping, Valves, Radiators & Controls
	In principle yes. Some heat pumps (I think including Daikin) appear to modulate the water pump to achieve a quasi fixed DT. So if you set it at 6 for the cold months it may stay at 6 even in the war...
	RE: New Fogstar 15.5kWh upright solution By Batpred, 2 days ago Forum Energy Storage
	For the common benefit, a quick update on this. Fogstar initially said they would support the Ginlong/Solis protocol on the Seplos BMS that they sell. We were going to try top have Seplos try to act...
	RE: Grant 13kW Aerona3 - issues getting zones to temp By JamesPa, 2 days ago Forum Air Source Heat Pumps (ASHPs)
	That all sounds promising, the right people, who hopefully understand what they are looking at, are finally on the case. Just one thought, if you are offsite when Grant visit perhaps you could consid...
	RE: Solis S6-EH1P8K-L-PLUS – Why I Chose It and What I’ve Learned So Far By Batpred, 2 days ago Forum Energy Storage
	Some of the circuits in my home are not protected by RCD (which is fairly common, the earth wire was often not even run for ceiling/lighting circuits). I am exploring this topic and whether it contri...
	RE: Mixture of copper and plastic CH pipework. Will it be ok, or need changing? By Bash, 2 days ago Forum Thermostats, Volumisers, Buffer Tanks, TRVs, Pumps, Piping, Valves, Radiators & Controls
	Yes, an elbow is what I should have said. The 22mm copper pipe from the boiler curves slightly into the ceiling and then the push fit elbow connects to the horizontal run of plastic pipe under ...