Ideal Heat Pump DHW settings
Hi all,
I was wondering if anyone had an idea of how the control of DHW works on the Ideal pre-plumbed cylinder (I also have a Halo Thermostat). I think I've located the correct setting in the installer parameters, 1620 - Release, which is currently set to '24 h/day'. My understanding of how this is working is that whenever the water temperature drops below my set point, it will switch on and heat the water back to 50 degrees.
This has led to it coming on in the evenings after washing up or running a bath for the kids, which is not ideal as at that point I won't need hot water again until the following day and if it's before 7pm it's costing me 40p/KWh!!
I would much rather it heat the tank between 1-4pm when we're on the cheapest rate and we have the sun to help us out, but when I've switched the hot water to timed on the Halo thermostat, it seemed to just ignore the settings and come on when it wanted.
The options under the installer parameters are:
- 24 h/day
- All time programs HC/CC
- Time program 4/DHW
- Low-tariff
- T'prog 4/DHW or low-tariff
It's not clear in the manual what any of them do, so if anyone has any idea of how I acheive what I'm after or if there is a document somewhere that spells out what the different settings actually mean I would be incredibly grateful!
Also, if anyone is aware of how to select the time the legionella cycle runs, that would be nice too, currently it runs once a week but I can't figure out how to specify when!
TIA
- 26 Forums
- 2,123 Topics
- 46.7 K Posts
- 32 Online
- 4,531 Members
Join Us!
Podcast Picks
Latest Posts
-
RE: Octopus Cosy & Octopus EV + bidirectional smart tariff, together. What, eh?
I've certainly seen that on their Ts & Cs page but ...
By Majordennisbloodnok , 5 hours ago
-
RE: Planning Permission May 2025
Where does it state this please? Im genuinely interest...
By JamesPa , 8 hours ago
-
RE: ASHP heat output monitoring
@carlo - not much better, is it. It looks more like a u...
By cathodeRay , 10 hours ago
-
RE: Renewables & Heat Pumps in the News
this document extensively describes (in a non-blame, ne...
By Judith , 13 hours ago
-
RE: Ecodan - Legionella Operation Time and Target Temperature
Once the white plastic cap is removed, my immersion loo...
By Old_Scientist , 1 day ago
-
RE: Replacing Refrigerant on Mitsubishi Heat Pump
@dgclimatecontrol I don't know, but they were not happy...
By DavidAlgarve , 1 day ago
-
RE: Why do we need pressurised systems?
A good question @toodles. My old open thermal store and...
By AllyFish , 2 days ago
-
RE: 300 Liter Tank - Do I have to heat it all?
Cross references for @martingale Background discussi...
By Transparent , 2 days ago
-
@ecobaker May I ask a question of you please. I too hav...
By Papahuhu , 2 days ago
-
RE: Share Your Experiences with Heat Pump Manufacturer Support
@terry1812 Oh Good! Pleased to help if I can! Regards, ...
By Toodles , 3 days ago
-
It's unclear to me how the Smart Control project work b...
By Transparent , 3 days ago
-
RE: Have Consumers Been Lied to About the Efficiency of Heat Pumps Made in China?
@pavel, this isn't about discrediting Chinese products....
By Mars , 3 days ago
-
RE: Solar Power Output – Let’s Compare Generation Figures
We had an excellent four months (11/3 to 15/7) generati...
By JulianC , 5 days ago
-
RE: Is this just haze or something more?
I think the present somewhat cooler hazy days show the ...
By Judith , 5 days ago
-
RE: My misgivings about installing ASHP and solar panels via the ECO4 scheme...
All noted and accepted and as I say I am sorry that you...
By JamesPa , 5 days ago
-
I think it is very much me that is sitting outside the ...
By Grantmethestrength , 5 days ago
-
RE: Who's your electricity provider and what's your tariff?
Aggregators have been recognised for many years, and it...
By Transparent , 6 days ago
-
RE: Help me keep the faith with my air source heat pump installation
Great news I edited my previous post (probably af...
By JamesPa , 6 days ago